Can't find trim screw - Jumbo RC JUMBO HELICOPTER

Steering Column Trim Cover Replacement

Important: You must check for 2 pan head tapping screws (1,2) in the lower trim cover before removal.
If necessary, remove the 2 pan head tapping screws (1,2) from the lower trim cover (3). Remove the lower trim cover (3).
If screws are not present in the lower trim cover, proceed to the next step.
Gently unsnap the lower trim cover from the upper trim cover.

Important: You must check for 1 TORX® head screw (1) in the upper trim cover (2) before removal.
If necessary, remove 1 TORX® head screw (1) from the upper trim cover (2).
If a screw is not present, remove the upper trim cover (2).

Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

it's a piece of cake.All you do is unsnap the radio/a/c bezel remove the screw's from the bottom of the cluster bezel and the cluster bezel will unsnap off the cluster and there is like 4 screws holding the cluster in.Then the bulbs just twist in and out. TRIM PLATE BEZEL REPLACEMENT - INSTRUMENT PANEL (I/P) CLUSTER REMOVAL PROCEDURE 1. Pull out on the accessory trim plate in order to release the retaining fasteners. 2. Disconnect the accessory trim plate electrical connector(s). 3. Remove the screw retaining the cluster trim plate to the center trim panel. 4. Lift up on the cluster trim plate to release the retaining fasteners. 5. Remove the cluster trim plate. INSTALLATION PROCEDURE 1. Align the retaining fasteners with the center trim panel. 2. Push on the outer edge of the cluster trim plate in order to secure the retaining fasteners. 3. Install the screw retaining the cluster trim plate to the center trim panel. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the cluster trim plate screw to 2.5 N.m (22 lb in) . 4. Connect the accessory trim plate electrical connector(s). 5. Align the retaining fasteners with the I/P. 6. Push on the outer edge of the accessory trim plate in order to secure the retaining fasteners.

Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal

1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
   

1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
   

1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.
   
   
   Trim Panel
   
   
   
   
   
   Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole

1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
   

1. Remove two screws located at bottom of front door trim panel.
   

1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
   

1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
   

1. Pull front door trim panel from the top to release hooks from front door .
   

1. Remove front door trim panel.
   

Installation

1. Replace any bent or damaged fasteners.
   

1. Follow removal procedure in reverse order.
   

Body Side
Removal

1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
   

1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
   

1. Remove forward and rearward mating sections from under window trim.
   

Installation

1. Replace all christmas tree fasteners.
   

1. Follow removal procedure in reverse order.
   

1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.
   
   
   
   
   

Back
Removal

1. Disconnect rear window defroster wires.
   

1. Remove the liftgate window garnish moulding as described.
   

1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
   

1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
   

1. Remove liftgate trim.
   

Installation

1. Follow removal procedure in reverse order.
   
   
   Liftgate
   
   
   
   
   

Let me know if this helps out.

Heater & Air Conditioning

1. Disconnect the negative battery cable.
   
2. Remove the screws securing the cluster trim plate to the instrument panel.
   
3. Tilt the top of the cluster trim plate downward releasing the clips that mount the bottom of the trim plate to the dash. Remove the trim plate.
   
4. Remove the screws attaching the accessory trim center plate to the dash.
   
5. Tilt the top of accessory trim plate downward releasing the clips that mount the bottom of the plate to the instrument panel. Remove the plate.
   
6. Remove the screws attaching the control assembly to the dash.
   
7. Remove the control assembly from the dash.
   
8. Disconnect the control assembly electrical connectors.
   
9. Remove the control assembly.
   

To install:

1. Install the control assembly.
   
2. Connect the control assembly electrical connectors.
   
3. Install the control assembly attaching screws.
   
4. Push the mounting clips into place and roll the top of the accessory trim plate upward into position.
   
5. Install the screws attaching the accessory trim plate to the dash.
   
6. Push the mounting clips into place and roll the top of the cluster trim plate upward into position.
   
7. Install the screws attaching the cluster trim plate to the instrument panel.
   
8. Connect the negative battery cable.
   

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 40; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Door Panels - REMOVAL & INSTALLATION

The many different design interiors make it impossible to list each fastener location. The trim panels that must be removed are held in place by screws and clips. These locations vary from model to model. After removal of all the fasteners that you are aware of, if the trim panel is still firmly attached, you probably missed a hidden fastener. If this happens, gently and carefully pry the area looking for the location that doesn't flex. The location that does flex is where you'll find the fastener(s) you missed. Screws and retainers are usually hidden. Handle trim, reflectors, light lenses and other plastic pieces usually cover the main retaining screws. Take great care with the plastic trim panels. Plastic trim panels are usually very hard plastic and extremely easy to crack. The following steps can be used to guide you through the removal and installation of the trim panels, but you may need to alter these steps to your specific needs.

1. Disconnect the negative battery cable.
2. Pull the inside door handle to the open position, unfasten the screw and remove the handle escutcheon.
3. If equipped with manual locks, remove door inside locking rod knob.
4. If equipped with manual windows, insert a suitable window regulator handle removal tool behind the handle. Disengage the retainer, then remove the handle.
5. If equipped with power windows and locks, use a small flat-bladed prytool to carefully pry the switch plate up, then detach the power component electrical connectors.
6. If equipped, remove the screws inserted through door armrest and pull handle assembly into door inner panel or armrest hanger support bracket.
7. Lift the seat belt trim panel up and remove the hidden retaining screws.
8. Remove the outside side view mirror trim plate retaining screw. Lift the panel up to disengage the retaining clip, then remove the trim panel from the door.
9. On styles with courtesy lamps located in the lower area of the trim panel, disconnect the wiring harness at the lamp assembly.
10. If equipped, use a suitable tool to pry the reflector plate from the side of the door panel.Remove bottom trim cover retaining screws, then remove the lower trim cover.
11. Remove any necessary electrical connector CPA clips, then unplug the electrical connectors.
12. On styles with integral armrests, remove the screws inserted through the pull cup into the armrest hanger support.
13. Unfasten the door trim panel retaining screws. The locations of the screws will vary depending upon the year of model of vehicle. The screws are usually hidden, so be sure to look carefully to make sure you don't miss any.After all of the trim panel retaining screws are removed, slide a suitable trim panel removal tool between the door panel and door perimeter to carefully disengage all of the trim panel retaining buttons. Make sure to position the tool close to the fastener, or the trim panel may be damaged.
14. Carefully lift the trim panel away from the door, checking to be sure all of the retaining buttons and screws and electrical connectors are unfastened.
    

To install:


Before installing the door trim panel, check that all trim retainers are securely installed to the panel and are not damaged. Replace damaged retainers as required.

1. Connect electrical components where present.
2. To install the door trim panel, pull door inside handle inward; then position the trim panel to the inner panel, inserting the door handle through the panel hole.
3. Position the trim panel to the door inner panel so that the trim retainers are aligned with the attaching holes in the panel, and tap the retainers into the holes with a clean rubber mallet. Install all previously removed items.
4. Install the remaining door panel components in the reverse order of removal.
5. After installation, connect the negative battery cable, then check for proper attachment and operation of electric components, if so equipped.
   

Hope helps (remember rated and comment this).

REMOVAL AND INSTALLATION Trim Panel —Front Door, Expedition Removal

1. NOTE: Release the top portion first.
   Remove the sail panel.

1. Remove the window regulator switch plate (14524).

1. Disconnect the electrical connectors.

1. Remove the upper door trim panel screw.

1. Remove the door trim panel screw at the window regulator switch plate opening.

1. Remove the door trim panel screw in the courtesy lamp housing.
   1. Remove the courtesy lamp lens.
   1. Remove the screw.

1. Remove the inside door handle trim cover.

1. Remove the inside door handle.
   • Remove the bolt.

1. CAUTION: To avoid damage to the front door trim panel, do not pull directly outward.
   Lift upward and then outward to remove the front door trim panel (23943).

1. Remove the courtesy lamp and socket.

1. Disconnect the power mirror electrical connector.

Installation

1. Connect the power mirror electrical connector.

1. Install the courtesy lamp and socket.

1. Install the front door trim panel.

1. Install the inside door handle.
   • Install the bolt.

1. Install the inside door handle trim cover.

1. Install the door trim panel screw in the courtesy lamp housing.
   1. Install the screw.
   1. Install the courtesy lamp lens.

1. Install the door trim panel screw at the window regulator switch plate opening.

1. Install the upper door trim panel screw.

1. Connect the electrical connectors.

1. NOTE: If a new trim panel is required: Some new trim panels have a cut out opening for the window switchplate that is larger than that on the original trim panel. When installing a new trim panel, install the window switchplate in the following sequence to make sure that the switchplate is secured fully into the door trim panel.
   Install the window regulator switchplate.
   • Insert the rear switchplate clip into the trim panel opening.
   • Install the forward and side clips into the trim panel opening.

1. NOTE: Install the lower portion first.
   Install the sail panel.

Door Panel

1. Remove the retaining screws from the armrest assembly.
   
2. Remove the screws retaining the switches to the housing and remove the cover assembly.
   
3. Remove the door trim panel retaining screws.
   
4. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.
   
5. Disconnect all the wiring, if so equipped, and remove the trim panel.
   

To install:

1. Position the trim panel to the door inner panel and connect the wiring, if so equipped.
   
2. Push the trim panel and retaining clips into the inner door panel holes and install the retaining screws. Install the screws retaining the switches to the housing.
   
3. Position the armrest to the trim panel, and install the retaining screws.
   

1. Remove the rear door power window/power door lock switch
2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
3. Remove the door trim panel screws located by the armrest handle.
4. Remove the door trim panel using J 38778.
5. Disconnect the electrical connectors.
6. Remove the door trim panel from the door.

INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

1. Install new trim panel retainers to the rear door trim panel.
2. Connect the electrical connectors.
3. Align the door trim panel retainers to the door.
4. Press the door trim panel at the retainer locations until the retainers are fully seated.
5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
6. Install the power window/power door lock switch