Question about Kitchen Appliances - Others

2 Answers

Sharp Weather Station Model SPC344 The outside temperature doesn't register and I can't find my manual I replaced the batteries in the weather station and everything works fine except the outside temperature doesn't register on the outside piece or the inside weather station.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

After inserting the batteries, DO NOT set the time until the OUTSIDE temperature registers. That's the trick.

Posted on Nov 06, 2011

  • stephaniesho
    stephaniesho Jan 10, 2013

    It worked!!!!!!!!!!!!!!!!!!!

  • hansen_rober Oct 09, 2017

    Wonderful that the answers are kept after all this time. It is very much appreciated. Thanks so much 'cause you have made life easier for me!!

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Bang the **** thing with a very large hammer

Posted on Nov 10, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have the Atomic Clock model W86111. I had to change the batteries on the outside device. The clock outside temp just flashes 63.5 all the time. How do I make it sync to the device outside?


Remove all batteries from outdoor sensor and weather station.

Press one of the buttons on the weather station at least 20 times to clear all memory.

Verify that the weather station is blank before proceeding (there may be lines painted on
the screen that will show when power is removed).

Leave both units without power for 15 minutes (very important).

Insert fresh batteries into the clock.

Insert fresh batteries into the outdoor sensor.

Press the TX button on the outdoor sensor to transmit RF signal.

Keep the outdoor sensor 5-10 feet from the forecast station.

When RF connection is established, the temperature will appear on the station. Allow the
outdoor sensor and weather station to sit together for 15 minutes to establish a strong
connection.

Oct 14, 2017 | Home

1 Answer

New la crosse technology wind speed weather station model # CA87092 set up.wind speed and outdoor temperature showed until this morning.new batteries used yesterday in setup. what is the problem?


The instructions for your station call for a specific set up procedure. Batteries should be installed in the transmitter first with time allowed for it to initialize and begin sending data. After installing batteries in the receiver, you should see wind speed and temperature displayed. BUT, here in the real world I have a Lacrosse receiver currently displaying a balmy 67 degrees inside and a not-so-balmy - - outside. I believe the alkaline batteries used in the transmitter lose efficiency or freeze at low temperatures. Warmer weather restores the outside temperature display.

Jan 05, 2017 | La Crosse Measuring Tools & Sensors

2 Answers

Why can't I receive input from the outside sending unit?


Make sure that all the batteries are good!!
This procedure outlines the typical process to pair the sensor and base.
Base Station Battery Installation

·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station. 1541 WeatherGuide Wireless Weather Forecaster with Barometer

Jan 07, 2016 | Measuring Tools & Sensors

1 Answer

Changed the batteries in both the transmitter and weather station. It doesn't show temperature on the transmitter or show temperature and humidity on weather station


In some of these weather stations, you have to install the batteries in the transmitter first and then the weather station within a certain time limit. Also, the weather station must be within a specified distance from the transmitter when replacing the batteries.

If you look on the weather station, there should be a make and model number. If you have that, you can visit the website (if there is one) and download an instruction booklet for your model.

Jul 21, 2015 | Measuring Tools & Sensors

1 Answer

Display station not showing outside temperature


Check battery status indicator on main weather station of remote unit. If no indication, replace battery in remote unit. If battery is good then check "channel setting" of remote unit to make sure the channel setting on remote unit matches the "channel" setting on main unit. many weather stations will take up to 3 or 4 remote units and they must use different channels to relay the remote imfo to the main weather station unit.

Jun 19, 2015 | Measuring Tools & Sensors

1 Answer

I cannot get the outside temperature to show on the inside monitor


Try the usual fix by removing batteries and reinstalling/replacing batteries starting with the outside unit. Wait for as long as 10 minutes for the ouside temperature to be displayed on the indoor unit. If nothing happens after 10 minutes, the outside unit may have failed.

Oct 20, 2013 | Oregon Scientific Bar806hga Helios Solar...

1 Answer

Why is the outside temperature not displaying on the base?


After a battery replacement, the outside and inside units have to "talk" to each other before you can get a display. Also, the outside unit's batteries have to be replaced first. You should not press any buttons for 10 minutes until the two units have finished "talking"

Jan 24, 2013 | AcuRite Acu-Rite 00593W Wireless Weather...

1 Answer

The sensor from my weather station is not registering outside temperature


I've had the same problem since I bought this unit 2+ years ago; when the outside temperature moves into the freezing zone, the sensor stops transmitting. I contacted Lacrosse-- all they could suggest was change the batteries. My solution: throw it in the trash!

Aug 05, 2012 | Bushnell Measuring Tools & Sensors

1 Answer

C Tech Weather Station. How do i reset the outside temperature. Meter says it's off?


Is the outside unit LED on? I replaced the battery on the outside unit and in doing this reset the outside information.

Jul 05, 2012 | Coghlan's CTech Wireless Weather Station...

1 Answer

Cannot get the weather station model ws-916ou-it to show outside temperature


I have three of these WS-916OU-IT units. After a few years, the outside sensor just fails. You will get dashes and a "TR" low battery signal, even if the batteries are good
just buy another whole weather station (short money) and set both the old and new weather station unit to receive from the single new outdoor sensor.
To do this - just follow the procedure for a single sensor - that is - put the batteries in the new sensor - then within 30 seconds - put the batteries in all the weather stations - they will all pick up the same outdoor sensor.
I now have three units running off of one outdoor sensor.
Seems a bit silly, but it works.

Feb 27, 2012 | Measuring Tools & Sensors

Not finding what you are looking for?
Kitchen Appliances - Others Logo

Related Topics:

3,155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Appliances - Others Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Irene Tulloch

Level 2 Expert

494 Answers

john h

Level 3 Expert

21895 Answers

Are you a Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...