The original code will not clear from my Weiser lock electronic lock. I have entered multiple codes and the original still stays. How do I get the original to clear.

[PDF]Quick Reference Installation & Programming Manual

www.weiserlock.com/.../electronics/smart...

Translate this page Weiser Lock25605-02 Weiser SmartCode Manual. Program. Button .... Press and hold the "LOCK" button on the exterior keypad, while fully inserting the battery pack into .... anyone withaccess to the power board can change these codes, you must restrict access ...technical means, or evaded by entry elsewhere on the property. No lock.

Which manufacturer made the keyless deadbolt lock? Make sure that the batteries are good in the unit.

I have an older Weiser Powerbolt deadbolt lock that is programmed by taking off the cover on the inside of the door. This model has handheld remotes and the keypad. Inside there are three yellow buttons. Two match the cover's lock and unlock buttons. Press and hold the third button (in the center of the set of buttons). Then enter program in the code within a few seconds and press the enter button to set the code. If the unit beeps again, the code is set. If the unit doesn't beep, retry from the press and hold the Program button step.

Another model of the Weiser Powerbolt lock has the Program button either on the top left or lower right hand side of the board (depending on the way the door opens) under the cover. Press the Program button once and then enter the 4-8 digit code. Press the Lock button to set the code. If you hear a long beep, the code was accepted; otherwise try to program your code again.

Kwikset Powerbolt locks are programmed the same way as the second Weiser Powerbolt described above.

Kwikset SmartCode locks have their Program button in the center of the bottom of the control board. Otherwise the programming is the same as that given above for the second version of Weiser Powerbolt locks.

MiLocks have three buttons in a horizontal line. The left-most button is the Set button. Press this then enter the code followed by the Unlock button. The code must be entered within 5 seconds of pressing set.

Baldwin Hardware's Boulder series of keyless entry deadbolts are programmed just like the Kwikset SmartCode units.

I don't know of any videos. Most manufacturers do have PDF files with the programming instructions.

I hope this helps. Please add more information about your deadbolt for extra assistance.

Cindy Wells
(I end up replacing the batteries often on the lock I have; it seems like they last 6 months or less.)

To change your code:

1. Remove the inner cover plate from the lock.

2. Locate the small round reset button near the left side of the circuit board (Red or Black).

3. To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

4. To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.

hope this helps

John

How do I change the access code (and delete my old code) on my Powerbolt 1000?
The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.

1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.
2. Press the PROGRAM button twice, enter the same new code and then press the LOCK button once.
3. Press the PROGRAM button three times, enter the same new code and then press LOCK once.

If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour. After the hour has passed, you may re-enter the batteries.

United States of America Customer Service Contact Information
Call Us Toll Free: 800-422-4278 (Mon-Fri, 6:00am - 4:30pm PST)

http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

Good luck, Elizabeth!

I can't help you directly, but Weiser customer support contacts can be found on this page:

http://www.weiserlock.com/en/CustomerService/ProductSupport/SupportContact.aspx

Good luck!

Weiser has a one year warranty against electronic problems and a lifetime warranty for mechanical and finish problems with their locks. Contact them from this link:

http://www.weiserlock.com/en/Products/SmartSeries/Powerbolt.aspx

Good luck!

1. To program the first code, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
2. To program the second code, press the reset button twice , then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
3. To program the third code, press the reset button 3 time, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

Good lock
Good unlock

• Remove the inner cover plate from the lock.
• Locate the small round reset button near the left side of the circuit board (Red or Black).
• To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
• To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.

best of luck.

Here's a free manual you can print out with complete installation and programming instructions you can keep for addressing any other concerns you might have in the future.

I thought this might be easier for you to work from, since you want to reset the lock prior to entering in your new master code and any other access codes you wish to let others use.

It is easy and straight forward to program and use.

http://www.smarthomeusa.com/Products/ED1460XXXX/manuals/WeiserLockPowerbolt1000-manual.pdf

Hope you find this Very Helpful - Best regards!

Here's a free manual you can print out with complete installation and programming instructions you can keep for addressing any other concerns you might have in the future.

I thought this might be easier for you to work from, since you want to reset your master code which will clear any other codes as well. You can then enter in all new codes to operate your lock.
It is easy and straight forward to program and use.

http://www.smarthomeusa.com/Products/ED1460XXXX/manuals/WeiserLockPowerbolt1000-manual.pdf

Hope you find this Very Helpful - Best regards!