Application Buttons i get no response from any of the application buttons on my hx2410. when i press the calendar button, the "align screen" comes up. i've tried both soft and hard resets, but with no luck...any help would be greatly appreciated!!!!

It depends on what application is causing the full screen mode. Try one of the following
- hit Esc key
- Hold Alt button, while pressing Tab - this will bring up all applications that are running - you can select the desktop.
- press Alt and F3 buttons together - this will close the application that is running in full screen.

It sounds like your nuvi would benefit from a simple screen calibration. You do this as detailed on page 47 of the manual. Since it is a very short procedure - I have transcribed it here for you.

1) Shut off the nuvi.

2) Press and hold the power button for about 30 seconds until the calibration screen appears (White screen with press dot").

Simply touch the dot as it moves on the screen. You might consider using a stylus or other relatively pointed object for the most accurate results.

That's it! If this was helpful, please rate it as such. Thanks & good luck!

Hello

Do not put lotion on your hands and do not touch the screen if your hands are wet. Any kind of moisture can affect the way the touchscreen operates. Moisture sometimes slows the response time from the screen to the operating system.

Check for a protective sheet on the screen. If there is some kind of a film or sheet on the touchscreen, the screen is likely not able to react to all of the sensitivities of the touch of a finger as it normally would.

If there is an application open and the touchscreen seems to not be working, simply close the application and retry it. A frozen application can usually be closed by pressing and holding on the circular button located just below the touchscreen.

Completely reset the phone by holding the "Home" button and the "Reset" button for a full 10 seconds until the phone resets.

THANK YOU FOR VISITING FIXYA

Have you already performed a clean reset? You might know that it will restore your device to its factory settings, thus deleting everything you have installed, as well as your personal data and settings. So, it is strongly recommended to backup your data beforehand.
Anyway, to perform a clean reset, press and hold the Calendar, Power, and Messaging buttons, and, whilst keeping them pressed, press and hold the reset pin with the stylus pen. When your device restarts, release the buttons and the stylus pen from the reset pin.
Hope it works for you.
Cheers! Carlos

To perform a hard reset you need to press buttons 1 and 4 in addition to the reset hole. This should do the trick.


The guidelines for resetting your phone is given below

Performing a Hard Reset

Perform a hard reset only when you want to clear all
user-installed settings, applications, and data from RAM
(Random Access Memory), where data and applications you have
loaded are stored.

CAUTION: If you perform a hard reset, your Pocket PC loses all data
and programs not saved in iPAQ File Store.

To perform a hard reset:

1. Press and hold down the Calendar and iTask buttons.
2. While holding down these buttons, use the stylus to
lightly press the Reset button on the bottom of the iPAQ
Pocket PC for about two seconds.

HP iPAQ hx2410 Hard reset

3. When the Pocket PC screen begins to fade, release the
Calendar and iTask buttons first, and then remove the stylus
from the Reset button.

Note: If you simultaneously push and hold the Reset, Calendar,
and iTask buttons for more than two seconds, the battery
disconnects. To restart the device, either plug the device into the
AC Adapter or press the Reset button again.
After performing a hard reset, you may need to reinstall
applications stored in iPAQ File Store to restore shortcuts and full
functionality.

4. The Pocket PC resets and powers on.

To return your iPAQ Pocket PC to factory settings after
performing a hard reset:

1. Tap Start > Programs > File Explorer > My Device.
2. Tap the iPAQ File Store folder to open it.
3. Tap Edit > Select All.
4. Tap and hold the selected files, then tap Delete.
5. Tap Yes to delete all file in iPAQ File Store.

To do the hard reset, while on battery (NOT A/C) power, hold down the two outside front-panel buttons (Calendar and iTask), While holding them, press the reset button with the stylus. Keep these buttons all pressed until the image on the screen begins to fade (about 4 seconds), then you can release the reset and application buttons. To restart your iPAQ, you must then plug the unit into A/C power, or do a Soft Reset by again, pressing the reset button with the stylus.

here is your answer
but if you want to solve your problem quick
microsoft takes 11$ to fix it

see this if this help you

Resetting the Device

Sometimes there is a need to reset your Pocket PC. Resetting the
device is known as performing a "soft" or "hard" reset.

Performing a Soft Reset

A soft reset stops all running applications, but does not erase any
programs or saved data. Be sure to save any unsaved data within
a running application before performing a soft reset.
Perform a soft reset to:
■ Stop all running applications
■ Install a new application
■ Restart the Pocket PC if it stops responding

To perform a soft reset:

1. Locate the recessed Reset button on the bottom of your iPAQ
Pocket PC.
2. Use the stylus to lightly press the Reset button.
The Pocket PC restarts and displays the Today screen.




Performing a Hard Reset

Perform a hard reset only when you want to clear all
user-installed settings, applications, and data from RAM
(Random Access Memory), where data and applications you have
loaded are stored.

CAUTION: If you perform a hard reset, your Pocket PC loses all data
and programs not saved in iPAQ File Store.

To perform a hard reset:

1. Press and hold down the Calendar and iTask buttons.
2. While holding down these buttons, use the stylus to
lightly press the Reset button on the bottom of the iPAQ
Pocket PC for about two seconds.


3. When the Pocket PC screen begins to fade, release the
Calendar and iTask buttons first, and then remove the stylus
from the Reset button.

Note: If you simultaneously push and hold the Reset, Calendar,
and iTask buttons for more than two seconds, the battery
disconnects. To restart the device, either plug the device into the
AC Adapter or press the Reset button again.
After performing a hard reset, you may need to reinstall
applications stored in iPAQ File Store to restore shortcuts and full
functionality.

4. The Pocket PC resets and powers on.

To return your iPAQ Pocket PC to factory settings after
performing a hard reset:

1. Tap Start > Programs > File Explorer > My Device.
2. Tap the iPAQ File Store folder to open it.
3. Tap Edit > Select All.
4. Tap and hold the selected files, then tap Delete.
5. Tap Yes to delete all file in iPAQ File Store.

Hi uninstall the application software for OSD from add/remove software .

Hold down the calendar and iTask buttons, and then press the reset button for about 6 seconds. The Pocket PC should reset and power back on. If the device does not power back on, make sure that the battery lock switch is set to the left.