Led with number 9 displayed is flashing

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

hi, it's a controller trip error message this can mean a bad connection or at worse a controller fault ...

Regards
Rob

That blink code is inverter failure. you have have some bad lamps in the display

MENU • Set Up • Searching For Yor Code • Blinking Back the Code:
Redefining a Key • Punch Through • Volume Default • Clearing Out
Key mover • Favorite Channel Scan • Macro-Sequence

How to Program your One For All remote
(Models URC-2005, URC-2099, URC-4005, URC-4050, URC-6050)



Set Up
After getting the proper codes from your manual or Customer Service, use the following instructions to enter them into your remote.


PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
ENTER the 3 digit code for your brand.
You should receive 2 quick flashes after entering your code.
PRESS the POWER button to test the code. (On VCR,LD,and CD players use PLAY)

menu
Searching For Yor Code
If you have tried all of the set-up codes for your brand of eqipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following proceedure to search for your code.

PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
ENTER 9-9-1 (two blinks on the remote)
ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER)
Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
When your device turns OFF, PRESS the MAGIC button and RELEASE it to lock in the code for your device.
menu
Blinking Back the Code:
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 0.
PRESS 1, carefully COUNT the number of blinks. (1st digit)
PRESS 2, carefully COUNT the number of blinks. (2nd digit)
PRESS 3, carefully COUNT the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.
This is your 3-digit setup code.
menu
Redefining a Key
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 2.
PRESS the DEVICE,(TV,VCR,CABLE,etc.),key you want moved
PRESS the DEVICE key you want to replace.
Example: If you want the Aux key to be a TV key:
"MAGIC" (2 blinks) 9 - 9 - 2, TV (you want to move TV)
Then AUX (you want to replace AUX).

menu
Punch Through
This sets Volume to work for one device in all modes.
For example, the TV volume will work in the cable and VCR modes.
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 3.

PRESS the device key you would like the volume to come from.

You will get two blinks on the remote.
NOTE: This only sets volume in the TV,VCR,CABLE, or SAT mode.
If you want to set the volume for a device to work just one or two other devices- refer to the instructions under "KEYMOVER-From one button to another"

menu
Volume Default
Use this to get the original volume to work on each device.

PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 3
PRESS the VOLUME+ key, you will get two blinks.

Now The volume is set for all original devices.

menu
Clearing Out
A Device Key
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 2
PRESS the device button twice. - Two blinks.
Any Button On The Remote
PRESS the button you want to clear - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 4
PRESS the button you want to clear twice. - Two blinks.
All Key movers,Macro's, and Defaults
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 8 - 0 -- Two blinks.
Scrambled Keypad
Sometimes it seems that the keypad is "scrambled". Functions like channels, volume, or numbers are not where they should be.
If your remote seems to be acting this way, try the following proceedure:

PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
ENTER 9-7-3 (two blinks) (for URC-2005, try 9-7-4)
Try the functions on the remote
If the keypad continues to act "scrambled", you may:
Be on the wrong code for your device.
A wrong code may only operate a few functions of your equipment or they may be operating inaccurately.
Have something more serious wrong with the remote.
In either case you will have to contact us for more information.

menu
Key mover
An Advanced Function To A Button
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 4.
PRESS the "MAGIC" button and then the three digit extended function.
PRESS the button you wish to use for that function - Two Blinks.
From One Button to Another
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 4.
PRESS the DEVICE and the FROM button
PRESS the DEVICE and the TO button
Two Blinks
EXAMPLE: To take the volume from a TV and put it in the VCR mode,
it would be: MAGIC - 9 - 9 - 4 -TV - VOL UP - VCR- VOL UP - two blinks.
You would have to do the same process for VOL DN and MUTE.


"Shifted" Key Mover
In order to stack a second function on a key; when pressing the button you want the function on in the sequence, instead hit MAGIC and then the button you want.
To use the function: TAP the MAGIC button and release, then TAP the key you chose.
FOR EXAMPLE:VCR-MAGIC(hold 2 blinks) 9-9-4 MAGIC 2-3-4 MAGIC PLAY
If you hit the PLAY button - the VCR will PLAY, if you hit MAGIC -PLAY it will bring up a display.

menu
Favorite Channel Scan
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 6
PRESS the channel to be stored, up to 3 digits
PRESS the ENTER button
REPEAT steps 4 & 5 up to ten channels
If you do not store ten channels, you have to hold "Magic" for four seconds to close Favorite Cannel programming.
NOTE: To stop scanning, press any other button on the remote control.

menu
Macro-Sequence
This will allow you do do several functions with just the touch of ONE key.
PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
PRESS and HOLD the MAGIC button until the red LED flashes twice, then RELEASE.
PRESS 9 - 9 - 5
PRESS the key you want the Macro to be on
PRESS the sequence of keys you want the remote to do
PRESS "MAGIC" and wait for two blinks - RELEASE.


When you hit the key you put the macro on it will automatically start the sequence.

IMPORTANT: The Macro key will be the macro in ALL MODES so it is best to pick a key you will not need for anything else in any other mode.

menu




All Material Copyright Universal Electronics Inc.
"One For All" copyright Universal Electronics Inc.
Any questions about the products should be directed to help(at)ueic.com

1. Turn on the component you wish to control
2. Press the button for the device you want to program.
3. Press and hold the [SETUP] button until the LED flashes twice.
4. Enter the code 9-9-1. The LED should flash twice.
5. Alternate between pressing the [POWER] key and the device key until your device shuts off, or use [PLAY] for VCR, LD, CD and DVD players. This may take some time as there are hundreds of codes.
6. When your device turns off, press the [SETUP] button to save. After you have configured your devices using the Code Search feature, you might need to find out which code was assigned.
   
   
7. Press the button for the device you want to program.
8. Press and hold the [SETUP] button until the LED flashes twice.
9. Enter the code 9-9-0.
10. Press the numeric button [1] and count the number of times the LED blinks. This represents the first digit of the four digit code. Press [2] for the second digit, [3] for the third digit and [4] for the fourth. If the LED does not blink, the number is 0.

I’m happy to help further over the phone at https://www.6ya.com/expert/al_e83b1941f9c0f302

Hello,

Follow the below instructions closely;

1. In order for this hack to work, you will have to send an infra-red code to your player with a OneForAll remote such as the OneForAll 6 (or URC7560) or OneForAll 4 (or URC7740) or OneForAll 4 Digital, or One For All 5 Digital (or URC 7555) with the following instructions:

* Press the DVD button
* Hold down the Magic button until the unit performs a double LED flash
* Configure your remote using the setup code 0 5 3 3

2. On your DVD recorder, using the official Sony remote, select the System-Menu option
3. On your DVD recorder, using the official Sony remote, select the Setup option
4. On your DVD recorder, using the official Sony remote, select the Options option
5. On your DVD recorder, using the official Sony remote, select the Command-Mode option
6. On your DVD recorder, using the official Sony remote, select the DVD1 option
7. On the official Sony remote, set the DVD1 option for the Command-Mode switch, under the sliding cover
8. Verify that both the official Sony remote control and your OneForAll remote control can power off and on your DVD player
9. Program your OneForAll remote with the following instructions:

* Hold down the Magic button until the unit performs a double LED flash
* Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
* Press the Magic button once
* Configure your remote using the setup code 1 8 9 or 0 0 1 8 9 if your remote only accepts 5 digit codes
* Press the 1 button once, a double LED flash should occur

10. Program your OneForAll remote with the following instructions:

* Hold down the Magic button until the unit performs a double LED flash
* Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
* Press the Magic button once
* Configure your remote using the setup code 2 5 5 or 0 0 2 5 5 if your remote only accepts 5 digit codes
* Press the 2 button once, a double LED flash should occur

11. Program your OneForAll remote with the following instructions:

* Hold down the Magic button until the unit performs a double LED flash
* Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
* Press the Magic button once
* Configure your remote using the setup code 0 9 5 or 0 0 0 9 5 if your remote only accepts 5 digit codes
* Press the 3 button once, a double LED flash should occur

12. Program your OneForAll remote with the following instructions:

* Hold down the Magic button until the unit performs a double LED flash
* Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
* Press the Magic button once
* Configure your remote using the setup code 2 2 1 or 0 0 2 2 1 if your remote only accepts 5 digit codes
* Press the 4 button once, a double LED flash should occur

13. Program your OneForAll remote with the following instructions:

* Hold down the Magic button until the unit performs a double LED flash
* Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
* Press the Magic button once
* Configure your remote using the setup code 0 7 9 or 0 0 0 7 9 if your remote only accepts 5 digit codes
* Press the 5 button once, a double LED flash should occur

14. Place your DVD player into Standby mode
15. Press the buttons 1, 2, 3, 4 and 5 on your OneForAll remote control, in order, one at a time
16. Your DVD player should show the words TIMER OK
17. Press the buttons 1, 2, 3, 4 and 5 on your OneForAll remote control, in order, one at a time
18. Your DVD player should return itself to Standby mode
19. Remove the batteries for significant period of time to wipe the programmed codes on your OneForAll remote

Good luck.

You are in the service mode now. The buzzer LED displays a flashing rhythm of 2 flashes while the ROM ID is show in the display(this is what you are seeing), press the buzz button to advance to the fault register level. Here is the manual to the tech manual http://laundry.manualsonline.com/mdownloads/89c212d9-4843-4409-b17c-b3439c9b0d05.pdf

I have the same problem and Dell have quoted $400 plus $200 to fit a new motherboard.

i cannot get my speakers to work, ( ANX68SEV-11d ) please help

1: Defective door lock switch
2: Defective electronic control board.

Get model and serial number of machine, enter model number on search engine and seek same like conditions. You should find solution to problem, or place model number here for me to correctly tell what is wrong.