Yamaha RX-V800 Remote Control

To perform a factory reset on a Yamaha RAV 352 remote for use with an RX-V2500 receiver, follow these steps:
1. Turn on the RX-V2500 receiver using its power button or remote control.
2. On the remote, press and hold the "VCR 1" and "ON/STANDBY" buttons simultaneously. Hold both buttons for about five seconds until the remote's indicator light blinks twice.
3. Release the buttons. The remote control should now be reset to its factory default settings.
4. Test the remote by using it to control the RX-V2500 receiver. Make sure the remote is within range and pointed towards the receiver's IR sensor.
If the factory reset doesn't resolve any issues you're experiencing with the remote control, you may need to try replacing the batteries or consider getting a replacement remote from Yamaha or an authorized dealer.
Please note that the steps provided are based on general instructions for Yamaha remotes, and there might be slight variations in the specific procedure for your RAV 352 model. Consulting the user manual for your specific remote or contacting Yamaha customer support can provide you with more accurate and detailed instructions tailored to your device.

To program your Yamaha RAV352 remote to your Yamaha RX-V2500 receiver, you can follow these steps:

1. Turn on your Yamaha RX-V2500 receiver.
2. Press and hold the "DVD" button on your RAV352 remote until the "DVD" button lights up.
3. Press the "Code Set" button on the remote.
4. Enter the code "30476" using the number buttons on the remote. The "DVD" button will blink twice to confirm the code has been entered.
5. Press the "Power" button on the remote to test if the receiver turns off. If it does, the programming was successful. If not, repeat steps 2-4 with a different code until you find the correct one.

If you're unable to find the correct code for your receiver using the above steps, you may need to try using the "Auto Search" function on the remote. To do this, follow these steps:

1. Turn on your Yamaha RX-V2500 receiver.
2. Press and hold the "Code Set" button on the RAV352 remote until the indicator light starts flashing.
3. Press the "Power" button on the remote to start the Auto Search function. The indicator light will continue to flash as the remote searches for a compatible code.
4. Once the receiver turns off, press the "Enter" button on the remote to save the code.
5. Test the remote by pressing the "Power" button to turn the receiver back on.

Hopefully, one of these methods will successfully program your Yamaha RAV352 remote to your Yamaha RX-V2500 receiver.

Rav-212

a couple of subtitutes:

$133 and $55

http://remotes.com/remotes/servlet/rs?a=gmi&smodel=RXV800&brand_pn=YAMAHA_RXV800&mode=large&uuid=A13001399186991

or you could buy a whole RX-V800 WITH a remote for $136 delivered...

http://cgi.ebay.com/Yamaha-RX-V800-5-1-channel-500-Watt-Receiver-/260751483460?pt=Receivers_Tuners&hash=item3cb5ffe244

Try this advice first:

http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641

"Dead" Remotes Can Be Saved

How to Re-Start Your "Dead" Remote Control

This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!

What if you DON'T use the remote? Does it shut down when just using it?

If SO, you have a bigger problem.

If NOT, it sounds like the remote is hosed - sending a code to shut off.

Do you have another remote of any brand that you could set to do something simple, like change volume? Don't train it from the original, though, or it would do the same thing.

Description: REMOTE CONTROL TRANSMITTER FOR RAV222 RXV800/1000/HTR5280 Only Numbers are allowed Model#: HTR5280-exploded view Availability: Pre-Order Price: $82.68 (USD) Part#: V6283501
The remote for the RX-V800 is the same as for the HTR5280.
Please contact the manufacturer for ordering, or contact one of their distributors, whose info is listed below.

Hope this helps!

Page link:

https://www.yamaha24x7.com/yamahaoms/ViewSchematic.aspx?ModelNumber=359096&SearchString=HTR5280

Distributor Ordering Information: HERMAN ELECTRONICS
7350 NW 35th Terrace
Miami, FL 33122
Phone: (800) 938-4376
Fax: (305) 477-8087
URL: http://www.hermanelectronics.com/OEMSearch.asp?Manufacturer=yamaha
VANCE BALDWIN ELECTRONICS
7060 State Road 84, Building 12
Fort Lauderdale, Fl 33317
Phone: (800) 432-8542
Fax: (800) 552-1431
URL: www.vancebaldwin.com

(I have the RX-V659). Because the Yamaha remote has TWO SEPARATE buttons - power ON and power OFF (standby). This problem can't be fixed. There's a code to choose power ON and another code for power OFF. But one button can't be two buttons. Bad engineering\ design by Yamaha in my opinion

email me .... [email protected]... ill send
you a copy of the codebook page... but let me try and locate it first, i have the same unit before. Yamaha code books are the same also to other models.

Reden

heres the manual hope it helps, i had the same problem with the replacement. its all in the dsp button. but check out the manual let me know if it helps. -NATE

it can be accessed via the main unit controls but you need to go through your manuals. Maybe you can get your remote repaired still... maybe not badly damaged caused by corrosion.

[email protected]