What's is the standard preprogramed code for smartcode locks

Here is the link to an excellent video of how to install, hand, and program the Smartcode 909. It includes switch-0controlled features of the lock:
http://www.kwikset.com/Videos/Vitro/smartcode.aspx

Here is an excellent video of how to install, hand, and program the Smartcode 909. It includes switch controlled features of the lock:
http://www.kwikset.com/Videos/Vitro/smartcode.aspx

Installation instructions:
http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

Called "handing" the lock (left-hand or right hand door hinges):
Remove the battery pack. Keep the door open.Hold down the "Lock" button on the exterior keypad and at the same time, insert the battery pack into the interior assembly. Keep holding down the lock button until you hear two beeps, which will take approximately 30 seconds. During that time, the Smartcode mechanism will automatically drive in and out several times to determine proper handing.Done!

There is an excellent installation & programming video where you can watch how to do this, and it also explains the features of the internal slide switches.

http://www.kwikset.com/Videos/Vitro/smartcode.aspx

Good luck!

Let's review the programming steps, in case you are overlooking something. This information was found at this link:
http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

Important before proceeding: 1. Verify that position #2 of the "Settings
Switch" is in the OFF position. (Refer to section 11.) 2. Work with the
door open (away from jamb) to avoid accidental lock out. 3. Make sure
the bolt of latch is in the extended (locked) position

8. Automatic - Bolt Direction Determination (Door Handing).
IMPORTANT: DO NOT SKIP THE FOLLOWING STEP.
LOCK WILL NOT BE ABLE TO OPERATE PROPERLY!
? In the steps below, the SmartCode mechanism automatically determines the "door handing" and sets the proper direction for motor to rotate.

a. Press and hold the "LOCK" button on the exterior keypad, while fully inserting the battery pack into the interior assembly (the tabs on the pack must face out)

b. When the unit begins to operate the bolt, release the "LOCK" button.

c. Do not disturb the unit for approximately 20 seconds until the interior Green LED flashes followed by a beep. During this time the system will drive the bolt several times, will determine "door handing", store data in memory and exit. It is very important that this process is allowed to finish properly.

Proceed with programming your Usercodes per the instructions.

Finally, here is the contact number for Customer Service At Kwikset. Call them if you still have the problem.

1-800-677-5625

Good luck!

Two User codes can be entered for your lock. Entering the two codes should over-write any old codes programmed into the lock.
Here is a link to the complete installation and programming guide for your lock:

http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

which you can cut and paste into your browser's search bar.

Good luck!

Here is the link to the installation and programming instructions for the 909-15 lock:

http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

It is a PDF file format, which requires that you have Adobe Reader installed on your computer to display properly. If you don't have it--http://get.adobe.com/reader/

It is a good time to replace the battery if you haven't done so already! Please carefully follow the programming instructions, because they can be tricky. If you goof up, simply start over.

Good luck!

This link will take you to the PDF image of the installation and programming instructions:

http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

(PDF files require that you have Adobe Reader or similar installed on your computer
http://get.adobe.com/reader/ )

It's a good time to replace the batteries while you're reprogramming. Please review each step carefully, because it's easy to goof up this programming process, if you don't follow the procedure properly.

Good luck!

The Kwikset 909-15 lock is a stand-alone device and is not designed to link to an external home security system.

Here is a link to the installation and programming instructions in PDF form--you will need Adobe Reader installed on your computer to open this file (http://get.adobe.com/reader/):

http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

For assistance or warranty information: call 1-800-677-5625 USA & CANADA
or visit, www.kwikset.com

Good luck!

Here is a link to the installation manual for your lock:

http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

You will find the reprogramming steps here. I'd suggest replacing the 4 AA batteries at this time, if you haven't already done so.

Good luck!

I'm including a link to the installation instructions for the Kwikset lock:

http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

Pay close attention to section 8, the instructions for programming a door for left or right-handedness.