Cn-sg0366zc power wires

Question edited for clarity.
Question moved to make model category from Cars and Trucks.

CN-NVD905U

Panasonic https://panasonic.ca > viewing > YEFM294342
Speakers. Connect the speaker wires. See the wiring diagram for the proper hookups. Follow the diagram carefully to avoid damaging the speakers and this unit ...
16 pages

Electrical Connections - Panasonic Strada CN-NVD905U ...

ManualsLib https://www.manualslib.com > manual > Panasonic-Str...
To prevent from damage to the unit, be sure to follow the wiring diagrams below.. Be sure to fully plug in the connectors. Secure them with clamps and ...

CN-NVD905U

Panasonic https://panasonic.ca > YEFM285972_ENG
Check the wiring in accordance with the wiring diagram. (Installation ... display " Strada" even after it has been disconnected from the system. Reset the ...

Panasonic Strada CN-NVD905U Service Manual [Page 29]

ManualsLib https://www.manualslib.com > ... > Service manual
Panasonic Strada CN-NVD905U Manual Online: Wiring Connection Diagram. ILLUMINATION SPEED REVERSE SIDE BRAKE CNP8 Vehicle signal connector 5 1 10P CN1921 6 1 ...

Panasonic Strada CN-NVD905U - Video - CNET

CNET https://www.cnet.com > roadshow > videos > panasonic-s...

2:14 The Panasonic Strada CN-NVD905U is a car stereo system that combines fast navigation with a user-friendly touch-screen interface and ...
CNET · May 21, 2008

..

there is no ignition module on k series engines. they are Coil Cn Plug, the igniter is built into the coil. each C.O.P has 3 wires going to it.
1 wire is for power (B+)
1 wire goes to ground (-)
1 wire goes to the ECU

The Wireless IP Camera from http://www.safer.net.cn
is intelligent for my baby monitor.

You might find the answer to the question in the user manual. Here is the link for the Panasonic Strada CN-NVD905U manual. I'd skip to page 14 to begin. Hope this helps you out.

Did you remove the dimmer switch or alter the wiring whilst putting the ceiling fan control in the wall? If so you have obviously wired it back up the incorrect way. How many original wires were at the light/dimmer switch. Will need to know colours etc?

Disconnect

CN SC20 on the SC board. Turn on the unit. Does the power LED
stay on?
Yes
SC Board
No

Connect

CN SC20. Disconnect

CN SS23 (*1) on the SS board. Turn on the unit. Does the power LED
Stay on?
Yes
SS Board
No

Connect SS23 (*1).

Disconnect CN D31and D32

on the D board. Is pin 5of CN P25 shorted
to GND?
Yes

Disconnect

CN P25. Is pin 5 of the socket P25 shorted
to GND?
Yes
P Board
No
D Board

Connect D31

and leave D32 disconnected.

Is pin 5 of CN P25 shorted

to GND?

Yes

Disconnect CB1-CB4.

Is pin 5 of CN P25 shorted

to GND?

Yes

No

C1 Board
Panel

No

Yes

No

D Board

Disconnect CB1-CB4.

Is pin 5 of CN P25 shorted

to GND?

Yes

No

C1 Board

Panel

Disconnect D31.

Connect D32.

Is pin 5 CN P25 shorted

to GND?

Yes

No

Disconnect CB5-CB8.

Is pin 5 of CN P25 shorted

to GND?

Yes

No

C2 Board
Panel

You have to seize the RID master for you domain, appears to be removed from network or can't be contacted, you can use the next commands in order to get the actual (MYSERVER should be replaced by the name of you server

C:\WINDOWS>ntdsutil
roles
connections
connect to server MYSERVER
q
Select operation target

then you get the next response:

Server "MYSERVER" knows about 5 roles
Schema - CN=NTDS Settings,CN=MYSERVER,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=MYDOMAIN,DC=net
Domain - CN=NTDS Settings,CN=MYSERVER,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=MYDOMAIN,DC=net
PDC - CN=NTDS Settings,CN=MYSERVER,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=MYDOMAIN,DC=net
RID - CN=NTDS Settings,CN=MYSERVER,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=MYDOMAIN,DC=net
Infrastructure - CN=NTDS Settings,CN=MYSERVER,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=MYDOMAIN,DC=net
select operation target:

the interested server is RID - this must be the name of a actual server, if this server is permanently down the you need seize the rol, use the next guide:

http://technet.microsoft.com/en-us/library/cc784077%28WS.10%29.aspx

if the server is an actual server you must review the event log in this server in order to get more clues of the error.

I recently had this message on my Westinghouse fridge. The CN and ER message stands for Connection Error. This is due to a power surge.
I suggest you disconnect the power cord from the powerpoint and switch off for 5 minutes.
When connecting, if you have a double power point use the other head as the initial one may be faulty and this may have caused the power surge.
Hopefully this will fix the CN ER message to disappear.

Second Opinion, if that doesn't help then send back!

please check www.playpower.com.cn