20 Most Recent
Mitsubishi WD-57733 57" HDTV - Page 3 Questions & Answers
Can you repair a dlp chip
It can be done if you can locate the right one (figure average 200 plus for part) but if a issue like dots etc better to get a replacement light engine and be done with it.Sometimes a "cheap" fix is not really a good one as replacing the display chip will not cure all issues.
About my tv
getting white spots on screen and more as time goes on? Damaged or bad optical light engine.
Tv with no picture. i just bought a new bulb but
Hello,
since you didn't get any picture, does the TV bring out sound? If the TV does not bring out sound, then it means the TV is having a power problem.
The clicking sound most of the time indicates a bulged capacitor on the power supply board of the TV. I think problem is with the power supply board and not the bulb.
But
more often bad capacitors causes problem on the power supply board. I
do not think the power board needs replacement, rather those defective
capacitors is causing this issue. Open unit up and take a look at the
power supply board.You will probably see one or more electrolytic filter
capacitors that are bulged up in the top-not perfectly flat like the
others.
The value of these capacitors will be different, most
likely they will be somewhere around-820 to 2200uF/25 V( or /10V
sometimes)
You can replace them with same values but I would
recommend the voltage rating to be higher(like 35V for an original 25V)
for reliability purposes.
What happens is,these bulged top
capacitors will cause a low and unfiltered DC voltage=main board will
malfunction(the relay will keep clicking until the caps are holding
enough charge to bring the voltage up over a threshold point).
You
can buy these capacitors at any Fry's or Radioshack store or you can
order them online at vendors like "mcmelectronics.com"(look for
electrolytic capacitors). After replacing these capacitor(capacitors)
most likely the normal operation will be restored. Or you can by a
refurbished complete power board to save you some stress from
www.shopjimmy.com.
Note: There may be also some other causes for
this symptom ,like a defective T con board ,or main board,but the bulged
top capacitors are the most common cause for this issue.
If you
don't know about TV repairers, take the TV to the nearest repairman to
fix the fault for you. Also, note that TV stores a lot of current, so
wait a while before opening the TV back cover.
I hope this helps.
Regards.
Model #57733 - Volume will
Hi,
the volume control is increasing randomly on it's own because the volume button on
the TV is partially stuck in, that is why its coming up occasionally.
This same thing may also happen to the remote control of the TV.
Use your find to rub the buttons on the buttons on the TV, especially the
volume control button. Do same on the remote and most definitely
problem should be solved.
Please give me a feedback if solution does not work for you.
Regards.
Error code 66 TV made a popping sound, then a
Hello
Error code '66' denotes Lamp did not turn On at P-ON sequence of no lamp inserted. There are two possibilities for the fault you indicates here. The fist one is damaged lamp. The second one is the fault with lamp ballast board. You reports that there was a 'POP' sound before the TV shuts down. So almp itself have the damage. But before replacing the lamp, the ballast aslo should be checked. It is a best practice to replace the lamp ballast along with the lamp. Just take the lamp out and check it. This is the picture of the lamp ballast board of your tV. If you send your email address to me by Fixya, I'll send a copy of the service manual for your TV by return mail. If you wants to repair it yoursef, and have a knowledge in electroncis, it will help you more. If you want anymore assistance from me, feel free to get be by Fixya. OK.
HDMI Inputs don't work (and I've tested my
The problem may be with the color oscillator of the circuit. Check first for swollen or leaking capacitors. Capacitors are cylindrical in shape and is black in color (color may vary) and has two legs soldered to the board. It may also be a faulty board based on the number of items damaged. You would have to need special tools to have this fixed or replace the board depending on the practicality.
My tv looks like it
the wd 57733 has sound but no picture and turns off on its own after a few minutes.
Not finding what you are looking for?