To find Cecilware 3K-GB-LD Cappuccino machine error codes like "ERR 1," refer to the machine's user manual or technical documentation. Alternatively, contact Cecilware customer support for assistance in diagnosing and resolving the specific error code on your machine.
Check the Operating Temperature:
Ensure that the machine has reached the correct operating temperature. If it hasn't, the indicator light will be on. Wait until the machine is fully heated before proceeding.
Check for Ongoing Programs:
If a rinse or cleaning program is currently in progress, the cleaning button may be flashing. Wait for any ongoing programs to complete before trying to brew coffee.
Inspect the Brewing Unit:
Make sure the brewing unit is properly seated and not obstructed. The brew group should be in the correct position.
If the brew group overflows, it could be due to a blockage or misalignment. Remove the brew group, clean it thoroughly, and reinsert it properly.
Inspect the Coffee Spout and Drainage Area:
Check the coffee spout for any clogs or blockages. Clean it if necessary.
Examine the drainage area at the bottom of the machine. If water is running away onto the floor, there may be a leak. Inspect the drip tray and other components for leaks or damage.
Refer to the Operating Manual:
Consult the operating instructions manual for your Schaerer Coffee Club machine. If the above do not resolve your issues, you may have to contact Schaerer Services.
Question edited for clarity.
These machine need dealer servicing every 6 to 9 months depending on usage. They don't tell you this when you buy them, but I have been fighting these types of machines for the 9 years before I retired. One place had 2 machines and another has 6. Once machine did 1,200 cups a days and was serviced every month. Airport Business Class Lounges.
..
They make a thousand models. It sounds like the heating element has failed. Generic help and videos in the link but these machines need dealer service at regular intervals depending on the complexity of the particular model.
https://www.google.com/search?q=Dolce+Gusto+coffee+Machine+no+hot+water
..
You can replace them but unlikely to repair them. The casing will come apart, with some difficulty.
Remove the old switch, source an identical new switch and fit it.
That .depends on software and configuration. It is not a universal code You might find help in the manual. CIMBALI M34 SELECTRON USE AND INSTALLATION Pdf Download ' ManualsLib
Inspect Electrical Supply: Ensure that the machine is receiving proper electrical power. Sometimes, an interruption in the power supply can trigger error codes.
Clean Components: Check if any components related to coffee grounds or filters are dirty or clogged. Clean the underpan gasket, filter holes, and filter holder outlet hole.
Coffee Ground Quality: Verify that the coffee grounds are of the correct consistency. If they are too coarse or too old, it can affect the machine's operation.
Discharge System: Examine the discharge system for any blockages.
The milk delivery tube is very narrow bore and in my experience you will find the tube is blocked with congealed milk solids even if you clean then regularly. You need an enzyme milk cleaner like Rinza and even with that you need to manually massage the tubes or remove the blockages. The service engineers just replace them.
The K111 coffee maker's red light typically indicates it's in the heating process. When ready, the light may change to green. The green line with ** suggests that it's in the brewing stage. If there's no water flow through the pod and it's noisy, check if the water reservoir is properly filled and securely placed. If the issue persists, consider contacting the manufacturer's customer support for assistance.
When the waterlevel gets high enough, a small magnet will float in a compartment at the bottom right, of the reservoir and give off the signal to a sensor.
Those floats either leak or corrode over time. What you describe can occur when it is pointing its magnetism in the wrong direction or even when it chooses to raise on its own terms. It is difficult to remove and replace those. Perhaps you can work the clamp loose, remove it and then fool the machine into thinking there is water, with another magnet attached. I have done it. You can see better if the float can be restored, when removed. Mostly it is both cracked open and filled with rust.
This sounds like there is an issue with the main circuit board inside the machine. Your best option is to contact a good repairer as this may need a more specialist repair.
Things you might try but turn it off before attempting repair.:
Check the flow meter and sensor: Open the machine and locate the flow meter and the sensor. Unplug the sensor and check the cables for any loose or rusty connections. Clean the connector and plug it back in.
Replace the flow meter and sensor: If the problem persists after checking and cleaning the connections, consider replacing the flow meter and the sensor.
Use manual or program mode: As an alternative, you can use the manual or program mode to control the water volume.
How to Fix Water Won't Stop Flowing on Breville Barista Express (youtube.com)