20 Most Recent
Cadence Weslo 927 Treadmill Walking Belt - Page 5 Questions & Answers
I have a cadence 70 e treeadmill someone gave
make sure the safety key is inserted. Then try the following:
# get a 12-18 volt dc battery fully charged(like one from a cordless drill)
# Make sure it is fully charged, because it won't work if not
# attach the + and - to the motor red is + and black is -
# If the motor turns slightly your motor is ok, if not the motor is bad and would need replaced
# if the motor is ok then your motor controller(the board with the metal) is malfunctioning and would need replaced.
Miles or kilometres
Go to iconservie.com click on manual input this info Manufacturer Weslo then Model name 920 their are 12 matches for this model for both standard measurement of distance.
Belt is slipping
This is caused by one of three problems. First and most likely, the
walking belt is loose. To tighten the belt, start by locating the two
bolts that adjust the rear roller (one on each side of the unit in the
back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a
time. Make sure that what you do to one side, you MUST do to the other
side or the belt will get off center. After you tighten it 1/4 turn,
check the belt to see if it is still slipping. If it is then tighten
the belt 1/4 turn again. Continue until the belt does not slip, but do
not tighten the bolts more than 2 full turns. If it takes more than 2
turns then something else is the problem. The second problem that it
could be is the drive belt might be loose. To tighten the drive belt,
start by removing the front cover. loosen the bolts around the motor
then tighten the drive belt by tightening the motor adjuster bolt. Once
the drive belt is tight, tighten the motor back down. The third
problem that it could be is the walking belt could be worn and need to
be replaced. Let me know if you have any questions.
Belt slips while walking
Sounds like the belt is loose. To tighten the belt, start by locating
the two bolts that adjust the
rear roller (one on each side of the unit in the back). Run the unit at
about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that
what you do to one side, you MUST do to the other side or the belt will
get off center. After you tighten it 1/4 turn, check the belt to see if
it is still slipping. If it is then tighten the belt 1/4 turn again.
Continue until the belt does not slip, but do not tighten the bolts more
than 2 full turns.
Whilst jogging hands free the treadmill belt
you need to lubricate the belt every 6 months or so. to do this lift up the belt and squirt some lubricant onto the belt board(not the rollers), do this on the left and right hand side.
you may also need to tighten the belt. this is normally done with an allen key, look at the end of the treadmill as if you were to walk onto it, and there should be a plastic cover on each side. look in here and you should see an allen key type bolt. turn each bolt one full turn. this will tighten the belt and stop it sticking.
Don't have a manual for my Weslo Cadence 2300
yes it is a battery thing, you have to pry gently up and the box will pop off there are 3 buttons in holes that hold it down. there is a short wire connecting to its back side, make sure you orient it correctly when replacing... the unit takes a 9 volt battery, you will see the place for it when you turn over the box.
Treadmill track will not run. It appears that the
under the hood after removing the 3 mtr hood screws in the frt. and the first screw on each side of the foot rails, there is a tech sheet/wire diagram. READ the sheet before making any moves to the controller- have item plugged in, 1 red led light should be lit,if not check on/off switch, if you have read the calibration section on tech sheet and proformed that task- control can be purchased and installed-then you can calibrate per its instructions. Best find a treadmill repairer,remember theres 120 volts there!!!
Cadence weslo 340 cs treadmill wont engage treadmill
If the transformer does not produce a "hum" the power is either not reaching the rectifiers or the rectifiers have died . Not likely if the machine was running last time prior to being put away. Try physically advancing the tread/belt to set the motor to a different contact starting point since corrosion (ambient humidity) may have dulled the motor contacts(brushes).
I was given a Weslo cadence 825 treadmill. I need
go to iconservice.com they have free manuals and also you may purchase replacement parts there as well. Be sure to get your model number before going to the site to make it easier (lower frame of the machine)
Good luck, Tim
Not finding what you are looking for?