Yukon Butt & Thigh Shaper - Page 9 - Answered Questions & Fixed issues

It sounds like there may be an issue with the control board of your Roger Black Gold treadmill. Here are a few things you can try to troubleshoot the issue:

1. Check the power supply: Make sure that the treadmill is plugged in and that the outlet is functioning properly. Try plugging the treadmill into a different outlet to see if that resolves the issue.
2. Check the control board: Inspect the control board for any visible signs of damage, such as burnt components or loose connections. If you see any damage, it is likely that the control board will need to be replaced.
3. Check the motor: If the control board appears to be in good condition, the issue could be with the motor. Check the motor for any visible signs of damage and test it to see if it is functioning properly.

If you are unable to diagnose the issue or fix it yourself, it is recommended that you contact the manufacturer or a qualified technician for assistance.

notify manufacturer for assistance

I would be interested to know what you mean by an old motor? Do you mean the motor that is fitted is not the original? Electronics often contain very sensitive components that is not surge protected are easily damaged by power surges or powerline transients. Motors too are often electrically very noisy that can cause damage if not efficiently suppressed.

Veridian Healthcare has the manual for the 19-005 pedometer on the product page: http://www.veridianhealthcare.com/product/19-005/ . See the Support tab. The direct link to the manual is currently: http://www.veridianhealthcare.com/wp-content/uploads/2016/08/93-1148-0913-IM-Pedometer-19-005-series.pdf . I hope this helps. Cindy Wells

Possibly this https://precor.mcoutput.com/108884/Content/SourceTopics/Err53.htm https://www.google.com/search?q=Pacemaster+Pro+Elite+error+53 ....

https://www.google.com/search?q=Pacemaster+Pro+Elite+re-calibrate+elevation ..

Error code 35 on a Pacemaster Pro Elite treadmill typically indicates a problem with the treadmill's speed sensor. This sensor is responsible for detecting the speed at which the treadmill belt is moving and providing that information to the treadmill's control panel. If the speed sensor is not functioning properly, the treadmill may display error code 35 and stop operating. There are a few things you can try to troubleshoot and fix this error:

1. Check the connections between the speed sensor and the control panel. Make sure that the connectors are securely plugged in and that there are no visible signs of damage.
2. Clean the speed sensor. The speed sensor may be dirty or covered in debris, which can affect its ability to accurately detect the treadmill's speed. Use a dry cloth to gently wipe away any dirt or debris.
3. Check the treadmill belt for proper tension. If the belt is too loose, it may cause the speed sensor to malfunction. Adjust the belt tension according to the manufacturer's instructions.
4. Replace the speed sensor. If none of the above steps fix the problem, the speed sensor may be faulty and need to be replaced. This is a more complex repair that may require the assistance of a professional.

I hope these suggestions help you resolve the error code 35 issue on your Pacemaster Pro Elite treadmill. If you are unable to fix the problem or if the error persists, it is recommended to contact the manufacturer for further assistance.

There could be a few possible reasons why your Reebok One GT40s treadmill is stopping suddenly after only a few minutes of use. Here are a few things you can try:

1. Check the power cord and outlet. Make sure that the power cord is securely plugged into the treadmill and the outlet, and that the outlet is functioning properly.
2. Check the treadmill's safety key. The safety key is a small device that helps to prevent accidents by shutting off the treadmill if it becomes disconnected from the control panel. Make sure that the safety key is properly inserted into the treadmill and the control panel, and that it is not damaged or loose.
3. Check the belt and deck. If the belt is slipping or the deck is not properly lubricated, it can cause the treadmill to stop suddenly. Make sure that the belt is properly aligned and tightened, and that the deck is adequately lubricated according to the manufacturer's recommendations.
4. Check for any visible damage or loose parts. If you notice any visible damage to the treadmill or any parts that are loose or not functioning properly, it may be necessary to have the treadmill serviced by a professional.

I hope this information is helpful. If the problem persists after trying these steps, it is recommended to have the treadmill serviced by a professional to ensure that it is functioning safely and correctly.

Error code E2 on a treadmill typically indicates a problem with the speed sensor. The speed sensor is a small device that measures the speed of the treadmill belt and sends a signal to the treadmill's control panel. If the sensor is not functioning properly, it can cause the treadmill to display an E2 error and prevent the belt from moving. There are a few potential causes of an E2 error on a treadmill:

1. The speed sensor may be loose or misaligned. Make sure that the sensor is securely attached to the treadmill frame and properly aligned with the magnet on the flywheel.
2. The speed sensor wire may be damaged. Check the wire for any visible damage, such as fraying or cuts.
3. The control panel may be malfunctioning. If the error persists even after checking the sensor and wire, the control panel itself may be the issue. In this case, it may be necessary to have the treadmill serviced by a professional.

I hope this information is helpful. If you continue to experience problems with your treadmill, it is recommended to have it serviced by a professional to ensure that it is functioning safely and correctly.

Check the speed sensor and its position. If its ok the the problem is with motor driver board . If you wish to get some details; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

If your Keys 8800 treadmill is not inclining even though the incline motor is running, it is possible that the worm drive shaft has become damaged or has become disconnected from the motor. This is a mechanical issue that will need to be addressed by a trained technician. I recommend contacting Keys Fitness or a qualified treadmill repair service to have the problem diagnosed and repaired. It is important to have this issue resolved, as using a treadmill with a damaged or malfunctioning incline mechanism can be dangerous.

No Service Manual. Contact the company https://www.manualslib.com/manual/1048680/Lime-Pro-Equipment-D-11-0-Performance.html?page=25 ..

It's a manual adjustment

Hi, it could be that there is too much friction between the belt and the portion of the machine below it. Try squirting some oil below the belt and let it run for a little bit before hopping on the treadmill again. Otherwise, you might need to have the treadmill serviced through it's manufacturer. Thank you.

Replica Watches

Question edited for clarity, full make model (what it is). Did you follow Section 9 about fully charging the battery, pressing and holding the button? Charging Instructions 1. Plug the charger into the mains - the charger indicator light will be green. 2. Turn on the battery by press and holding the power button until the green light is illuminated. 3. Plug the battery into the charger. The charger light will turn from green to red to indicate the charging process has started. 4. Once the battery is fully charged, the charger status light will be https://www.powakaddy.com/wp-content/uploads/2021/02/LATE-2022-FX3-OWNERS-MANUAL_01b.pdf If that doesn't fix it, it will be a warranty issue. Click Support on top left. https://www.powakaddy.com/manuals-and-instructions/ ..

Hi, usually you have a power button on the machine that you can press once to shutdown and once again to power up. It looks like a circle with a vertical line intersecting the top. So you can press that twice with a 15 second pause in-between presses. Thank you.

worn put parts inside, need to be serviced all machines on earth do that,

Here is a PDF Guide for the Following: Precise Comp U Step Electronic Pedometer Guide ~ https://drive.google.com/file/d/1ZzyANmdcsyVJuYvdGld-kOaj0qzdq9An/view?usp=sharing Shared from My Google Drive ... Your Are Welcome - Please Leave the Document Intact & Not Modified !!!