West Bend 33600 Coffee Maker - Answered Questions & Fixed issues

According to West Bend, not cleaning it, especially the heating unit well, will cause this. Here's the link for your manual. Go to page 3. This manual covers 3 models, including #33600. http://www.manualslib.com/manual/189911/West-Bend-13500.html#manual

Possibly a short in your power cord. Try plugging into a different outlet before replacing the cord. Also make sure the contacts where you plug the cord into the coffee pot are clean and not loose/broken.

THE PART NUMBER HAS BEEN CHANGED
IT IS #P200-97 AND YOU CAN FIND IT AT
HERITAGE PHONE # 1800-458-5593

often happens when using the Westbend and other appliance on the same circuit. Once the coffee is perked heat maintenance is no problem for the circuit, but two heavy users on the same circuit, i.e., coffee maker and microwave or coffee maker and roaster oven is asking too much

THE PART NUMBER HAS BEEN CHANGED IT IS P200-97
YOU CAN FIND IT AT HERITAGE
THE PHONE NUMBER IS 1-800-458-5593

What year was the 7210 made in?

I can't say how much cups but if you want to make 60 ounce coffee Then you need 3.25 ounce ground Dunkin coffee Let 10 ounce each cup so for 100 cups you need 1000 ounce coffee. For that (3.25*1000)/60. =54 ounce ground Dunkin coffee Thanks Please rate my work I gave you a very good answer

Try ordering online here; you may need to select the complete Faucet Assembly:

http://www.westbend.com/catalog.cfm?dest=itempg&itemid=946&secid=87&linkon=subcategory&linkid=125

The West Bend Large Capacity Coffemakers do not use replacement filters. The manual for the West Bend 33600 Large Coffee Urn is available here:

http://www.westbend.com/supportdata/L5613B_LargeCapacityUrns-All.pdf

Use an electric perk or regular grind coffee in the percolator basket rather than a 'drip' or finely ground coffee that would require a filter.

If you require a new basket, please see the West Bend on-line replacement part site here:

http://www.westbend.com/catalog.cfm?dest=itempg&itemid=946&secid=87&linkon=subcategory&linkid=125

The Instruction Manual for your coffee maker can be found here:

http://www.westbend.com/supportdata/L5613B_LargeCapacityUrns-All.pdf


100-CUP MODEL #33600

Water Level Measure of Ground Coffee

100 cups 6 ¼ cups

80 cups 5 cups

60 cups 4 cups

40 cups 2½ cups

Do not make less than 40 or more than 100 cups of coffee at one time. Use electric perk or regular grind coffee; a filter liner is not necessary.

I read your question but I am slightly confused... I see that you use it to heat water only, I presume that it is for tea or hot choc. Since you say it is new... Have you always used the perkolator parts? This unit is not designed to work without these parts. There is a thermocouple that helps regulate the water temperature, If the perk parts (the basket and the rod placed correctly in the bottom heating element) there is a good chance that is causing a problem. Try 1/2 pot of water and the parts I mentioned in place (as if you were going to perk coffee) and try it again, I think it will heat correctly and give you satifactory results. As far as the "blackening" it maybe "Brillo'ed or SOS pads to clean unless you have the plastic basket, the metal parts can be scrubbed. I hope I have understood your question correctly. Good Luck!
Douglas

THE PART NUMBER HAS BEEN CHANGED
IT IS P200-97 AND YOU CAN FINDE IT AT HERITAGE
THE PHONE NUMBER IS 1-800-458-5593

THE PART NUMBER HAS BEEN CHANGED IT IS P200-97
YOU CAN GET IT AT
HERITAGE
THE PHONE NUMBER IS 1-800-458-5593

There is an o-ring that is in there to seal keep the seal between the spout and the level. However, that seal is not available as an individual piece from West Bend. The spout and level come complete as one unit.

There is a short in the unit somewhere. It can be the power cord or it can be internally in the coffee maker. You can test the power cord before replacing it with a multimeter. Set the multimeter to OHMS. Take the power cord and connect the red probe to one connector on one end of the cord. Touch the black probe to both connections at the other end. You should only get a reading on one of the connections. Repeat this with the other connector. If you get a reading on both connections then the power cord is shorted out and must be replaced. In other words you should only have continuity on one of the 2 wires in the power cord. If it shows continuity on one connection on one end of the cord and 2 connections on the other end you have a short.

1 unit doesn't heat remove power; replace the thermal fuse: it looks lik a a bullet with a wire on each end; it is connected to the heating element radio shack sells them.

2 unit remove power; locate the short in the heating element wiring using an ohmmeter

contact west bend customer service 866-290-1851

You can download the manual for your West Bend coffee maker from this page:
http://www.focuselectrics.com/catalog.cfm?dest=itempg&itemid=30&secid=54&linkon=category&linkid=62

Here you go:
http://www.focuselectrics.com/catalog.cfm?dest=itempg&itemid=30&secid=54&linkon=category&linkid=62

Have fun!

As far as I know it does not have a spring. (At least the one we have where I work doesn't have a spring and it seems to work fine without one. But the urn was there before I started, so maybe at one time it had one.) Replacement parts are available here, and they list a stem but don't mention any spring.

Hope this helps. Thanks for using Fixya!