Question about 2009 kawasaki Ninja 650R

2 Answers

My 2009 kawasaki ninja 650r was stolen early in the morning and was recovered the next day.ignition switch was damaged and now replaced but now it takes a long time to get the engine running.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 96 Answers

That really sucks! Ive been there so i feel your pain but youre lucky you got it back. Was the bike dropped or crashed or laying down for any length of time?

Posted on Feb 02, 2019

Testimonial: "When I went to claim my bike back it was upright but my lower left and right belly cowl fairings were broken but no signs of it being laid down.just the ignition switch was broken from the bottom and after replacing the ignition switch from ebay my bike all of a sudden won't start as it used too I dont hear the fuel pump turning on I had to keep turning the key to off and on position numerous times to get the fuel pump to turn on I've checked fuses,connectors,wires that might of been tampered but so far nothing"

  •  mike
    mike Feb 19, 2019

    The Cheap chinese ignition switches on ebay can can cause issues. Ive seen a couple not work right from brand new. If you need to cycle the Key multiple times for the fuel pump to work then the kill switch part of it may not be working as well. You should tell the seller what its doing and make them send you another one.

  • Lloyd Villanueva
    Lloyd Villanueva Feb 19, 2019

    thank you mike! I very much appreciate your help and yes you're right the cheap ignition was the problem now she starts like new again! THANK YOU SIR!

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • kawasaki Master
  • 5,503 Answers

I got this free Pdf manual from an online store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the all the times I fixed the chipper in these 4 years

Posted on Jan 30, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: how do i replace the fuel pump on a 1992 gmc sonoma?

The fuel pump is in the tank, tank can be droped out to chg.pump, Its up to you how you want to do it but for me i always found it easier to unbolt the bed and lift it back about a foot and i could get right at it, and i did not have to mess with the tank straps and fuel lines, If that is the problem. Chk.fuses and relay first.

Posted on Mar 20, 2009

  • 80 Answers

SOURCE: Rough Idling, start-up early morning, until engine heats-up

this may be a sticking air flue meter take a matchstick .and push it into the hose this will let more air in if this works change the air flue meter

Posted on May 04, 2009

  • 149 Answers

SOURCE: i need a wire color diagram for the ignition

http://www.carlsalter.com/motorcycle-manuals.asp

Posted on Aug 31, 2009

Adrian762
  • 425 Answers

SOURCE: I need the color codes for the ignition sysem of a

There is wiring diag for an EL250E, that may give you a good guide or maybe even one of the other manuals. Check them out, you never know, http://www.carlsalter.com/motorcycle-manuals.asp

Posted on Jan 02, 2010

Thermo King
  • 593 Answers

SOURCE: 2008 kawasaki ninja 650 R generator cover replacement

You can take the cover off, nothing should fall out.

Posted on Jan 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Kawasaki Ninja 650R wiring diagram


Hi, Jason for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2006 Kawasaki Ninja 650R wiring diagram Google Search
Kawasaki Motorcycle Wiring Diagrams
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
Kawasaki 2009 ER 6f Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Oct 20, 2017 | 2006 kawasaki Ninja 650R

1 Answer

Why is the overheating light coming on so soon


Hi, Paula you may have a faulty temperature light circuit grounding out causing the light to come on check your wiring, for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Overheating on 2009 Ninja 650
Ninja 650 temp light coming on
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
Kawasaki 2009 ER 6f Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 29, 2017 | 2009 kawasaki Ninja 650R

1 Answer

Hi, I just replaced my 2006 Kawasaki Ninja 650r engine, unfortunately, in the process, I mixed up my stick coils and I'm unsure as to which one goes where or at least how to ID them.


Hi, Ernie for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kawasaki, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Kawasaki ER 6f ABS Service Manual
OEM Parts for Kawasaki
Kawasaki NINJA 650R User Manual
http://personalmanual.com/download/1594
Kawasaki Ninja 650R 2007

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 28, 2017 | 2006 kawasaki Ninja 650R

1 Answer

My 2012 ninja 650 wont let me turn key to on position


Hi, Milad for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Key won turn to the on position
Ignition switch won turn ITS STUCK
Ignition key won turn on 2004 Ninja 250R motorcycles
http://mototh.com/files/kawasaki/Ninja-650R/Kawasaki-Ninja-650R-Service-Manual-EN.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 04, 2016 | 2012 kawasaki Ninja 650

1 Answer

Why wont my 09 ninja 650 run


Hi, Keith and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Fuel line to the carburetor or throttle body pinched or kinked.
8. Carburetor float stuck.
9. Fuel injectors clogged.
10. Severely discharged or damaged battery you need 12.5 volts or better and be able to pass a load test if necessary.
11. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
12. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and CDI box.
Spark plug cables in bad condition and shorting check for leakage in the dark, cable connections loose, or connected to the wrong cylinders.
13. Ignition timing incorrect due to a faulty MAP, CKP, O2, TPS, sensors.
14. Faulty neutral, clutch lever, or kickstand safety switch.
15. Faulty fuel pump or fuse or relay.
16. Faulty CDI box.
17. A stuck bent or burnt valve.
18. Tip over sensor needs a reset.
19. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2009 Ninja 650R Won Start Please Help
2009 Ninja 650R Won Start Please Help Kawasaki Forums Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
Kawasaki 2009 ER 6f Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 01, 2016 | 2012 kawasaki Ninja 650

1 Answer

2009 Kawasaki Ninja 650R neutral light stays on all the time


Hi, John and the usual suspects are:
1. Neutral light bulb burnt out.
2. Faulty neutral switch.
3. A loose bulb in the socket.
4. Faulty wiring from the neutral switch to the light.
5. If the neutral light stays on while the bike is in gear the wire from the light to the neutral switch is grounded.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Neutral Light Stays On Ninja 650R Kawasaki Forums
neutral light always on KawiForums Kawasaki Motorcycle Forums
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
2009 Kawasaki Ninja 650R Owner Manual

Apr 15, 2013 | 2009 kawasaki Ninja 650R

1 Answer

2009 Kawasaki Ninja 650R how to change the battery


Hi, Comyns for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2009 Kawasaki Ninja 650R how to change the battery Google Search
2012 2016 kawasaki Ninja 650 Battery Install Removal
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
2009 Kawasaki Ninja 650R Owner Manual

Feb 20, 2012 | 2009 kawasaki Ninja 650R

1 Answer

Will 2009 ninja 650r forks fit on a 2007 ninja 650r?


Hi, Vince after careful deliberation 4 out 5 Kawasaki Gods give this one a thumbs up, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
My Front End Swap KawiForums Kawasaki Motorcycle Forums
The Fork Swap Informational Thread
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
2007 Kawasaki Ninja 650R Owner Manual

Oct 23, 2011 | 2007 kawasaki Ninja 650R

1 Answer

2009 Kawasaki Ninja 650R quit running while riding


Hi, Jasonstutzma and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike shut off while riding Page 2 KawiForums Kawasaki Motorcycle Forums
Bike died while riding down highway Kawasaki Vulcan Forum Vulcan Forums
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
2009 Kawasaki Ninja 650R Owner Manual

Aug 22, 2011 | 2009 kawasaki Ninja 650R

1 Answer

2006 Kawasaki Ninja 650R how to set the ignition timing


Hi, Racerx_005 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2006 2011 ZX650R Ninja
Kawasaki ER 6 Ninja 650 Rozrzd Timing chain Camshaft chain
Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
2006 Kawasaki Ninja 650R Owner Manual

Jun 25, 2011 | 2006 kawasaki Ninja 650R

Not finding what you are looking for?
2009 kawasaki Ninja 650R Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5809 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

richard libby

Level 2 Expert

202 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...