I have a 2001 honda f4i fi light is flashing anybody know what that code means

7 = Coolant Temp sensor or wiring.

A long blink = "10"
A short blink = "1"
DNS = Engine does not start
EON = Engine operates normally

BLINKS : PROBLEM, SYMPTOMS
No blinks: ECM malfunction, DNS
No blinks: ECM power / ground circuit malfunction, DNS
No blinks: ECM output line malfunction, DNS
No blinks: MIL circuit malfunction, EON
Stays lit: Data link circuit malfunction, EON
1 blink: MAP sensor circuit malfunction, EON
2 blinks: MAP sensor performance problem, EON
7 blinks: ECT sensor circuit malfunction, Hard start at low temp
8 blinks: TP sensor circuit malfunction, Poor performance on quick throttle operation
9 blinks: IAT sensor circuit malfunction, EON
11 blinks: Vehicle speed sensor circuit malfunction, EON
12 blinks: No. 1 Primary injector malfunction, DNS
13 blinks: No. 2 Primary injector malfunction, DNS
14 blinks: No. 3 Primary injector malfunction, DNS
15 blinks: No. 4 Primary injector malfunction, DNS
16 blinks: No. 1 Secondary injector malfunction, DNS
17 blinks: No. 2 Secondary injector malfunction, DNS
18 blinks: Cam pulse generator, no signal, DNS
19 blinks: Ignition pulse generator, no signal, DNS
21 blinks: No. 1 O2 sensor circuit malfunction (California only) , EON
22 blinks: No. 2 O2 sensor circuit malfunction (California only), EON
23 blinks: No. 1 O2 sensor heater malfunction (California only), EON
24 blinks: No. 2 O2 sensor heater malfunction (California only), EON
33 blinks: E2-PROM in ECM malfunction, EON
48 blinks: No. 3 Secondary injector malfunction, DNS
49 blinks: No. 4 Secondary injector malfunction , DNS

Hi. There ae numerous forums/site for your bike's FI codes. Since I don't know what code your FI is flashing, all I can say is put the FI code into your computer google or yahoo search area, and you will get an answer. Yiur FI should flash a few times first, and that is the first digit in the sequence. A second later, it should flash again, and that is th 2nd digit in the code. an EXAMPLE is 2 flashes, pause, 3 flashes...then repeats. That will be a code 23. Trust me, you will find the FI code online. Good luck!

FI means fuel injection and your bikes computer is picking up a problem and letting you know that maintenance has to be performed for peak efficiency. you can go to the dealer and have them read the codes and you can decide whose going to do the repairs. or just try some Seafoam, buy it at Autozone pour 1/3 to 2 gallons fuel, it wont hurt it, and ride it around getting on every once in awhile, for about 10 to 15 miles, then you might have to disconnect the battery to reset the light...these are just the cheapest things to try. let me get some feedback on this thanks!

you have a fi fault revmove the seat cowl on the left hand sise you will see the cdi unit (black box with wires going to it) you should see a black conector with two wires going to it bridge the wires with a pice of wire or split pin turn the igntion switch on and count the blinks one long one means ten recored the the blinks and phone a dealer and ask them for the fault code.to reset the the light pull out the bridge and the light should stay on or blink repeted turn off the switch make sure the kill switch is set to run hope this helps

it's probably leaking from the carb and down the cylinder into the crankcase.
it is probably due to a stuck float in the carb. take the float bowl off and make sure it is clean. the float can also be full of gas not letting it float up and stop the gas flow. the carb will fill up and leak wherever it can which is likely the case