20 Most Recent
2006 Honda VT 125 Shadow Questions & Answers
Hi my honda vt125 2003 is not charging any advice would be gratefully recieved
Hi this can be many thingsmeasure the voltage across the battery when engine running. shd be 13.5 -15volts rising with revs with a fully charged batteryIf not check all connections are clean & fastCheck stator coils have the correct resistancelastly check diode drop across the regulator rectifierRide SafeBike-Doc
Hi, after just rebuilding my
locate the wires that go to the switch which is just by the brake pedal disconnect them, and with ignition on touch them together, this should put brake light on, if not you have a wiring fault before the switch, if the light comes on then it is switch problem. could just need adjusting to suit the pedal travel.
Hi
i have a honda
Have the timing chain inspected. Normally these can be adjusted easily
Knocking from the clutch!!what could
The only thing I can think of is a broken gear tooth on the outer clutch hub. Remove the right engine side cover and check the clutch hub and the crankshaft drive gear.
Honda PC50 moped VIN decoder
To read the serial number on a Honda PC50 moped, follow these steps:
Locate the VIN (Vehicle Identification Number): The VIN is a unique code that provides information about your moped. On a Honda PC50, you can find the VIN in the following places:
Under the Air Filter Cover: Look on the left-hand side, just above the engine. The VIN should be stamped there. It typically looks like this: PC50 - 1234567.
Frame Number: The frame number is another term for the VIN. It's usually located near the air filter body.
Decode the VIN: The VIN contains important details about your moped, including the year of manufacture. Here's how to interpret it:
The 9th digit of the VIN is a check digit.
The 10th digit represents the year code. For example:
A = 1980
B = 1981
C = 1982
D = 1983
E = 1984
F = 1985
G = 1986
H = 1987
J = 1988
K = 1989
L = 1990
M = 1991
N = 1992
P = 1993
R = 1994
S = 1995
T = 1996
V = 1997
W = 1998
X = 1999
1 = 2000
2 = 2001
3 = 2002
Note that if your scooter was manufactured between February 1986 and February 1987, it's likely to be a '87 model;
Additional Resources:
If you have the full VIN, you can use the NHTSA VIN decoder to get detailed information about your moped.
Alternatively, you can call Honda with your VIN, and they will provide you with the necessary information.
4/23/2024 11:45:02 PM •
Honda...
•
Answered
2 days ago
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
Not finding what you are looking for?