2004 Aprilia RST 1000 Futura - Answered Questions & Fixed issues
Notch front end on Aprillia futura
This needs attended to right now! Both of the things I mention below can kill you if they are not attended to immediately!
If you mean the steering is notchy the upper and lower steering head bearings must be replaced and adjusted by an experienced person. Major safety issue, not to mention the wear on the bearing races and the cost of repair to those.
If you mean the suspension travel is notchy then do not ride it anywhere but to a shop to rebuild your forks.
I need to know how
On the left side of the dash there is a key lock. This is connected to a cable that goes under the seat and back to a latch.
Turn the key and lift the rear of the seat - pull backwards and upwards.
Need rear wheel for an
Hi.
You can purchase the wheel here. If you do not live in UK call them to arrange overseas delivery, the part distributors ships worldwide.
Depending on the color the wheel is p.n. AP8108821 or p.n. AP8108965 . You can find more sellers using the part number in Google.
Below also the part diagram. The wheel is part nr.4:
Regards.
Ginko
Starter motor
It sounds like your starter moter needs new brushes and servercing it sounds like it is not spinning over quick enough to fire the motor over fast enough.Get a firm in your local area that do every thing to do with starter moter alternators .Have a look in your local yellow pages
Rst 1000 futura rev
Hi! Please do replace the instrumental panel for this surely is faulty. No worries for it will really reach it's break point, it's inevitable. Hope this helps and good luck! Thank you for using FixYa!
My aprila rs50 starts fine and runs fine cold but if it heats up abit you pull the throttle and it sounds like its dieng
Instructions
-
-
1
Park your RSV 1000R on a well-ventilated, level area, using its kickstand.
-
2
Start the engine and let it idle in place until the
temperature gauge built into the instrument cluster indicates a minimum
internal temperature of 180 degrees Fahrenheit. This is the motorcycle's
ideal operating temperature.
-
3
Take note of the engine idle speed, using the tachometer
needle, while the engine is running. Ideally, the engine should idle
steadily at 1,250 rpm.
-
4
Adjust the engine idle speed to 1,250 rpm, using the idle
adjuster screw hidden between the lower right edge of the fuel tank and
the upper edge of the right middle fairing panel. Turn the idle adjuster
screw clockwise to increase the engine idle speed, or counterclockwise
to decrease the engine idle speed, using a small flat screwdriver if
your RSV 1000R's frame (VIN number) precedes ZD4MEE009YS000292. A
plastic knob allows the engine idle speed to adjusted by hand on RSV
1000R models with a frame (VIN) numbers starting from ZD4MEE009YS000293.
-
5
Rev the engine two to three times and observe the
tachometer. The engine should return to a 1,250 rpm idle. Adjust the
engine idle speed as needed, using the method described, then rev the
engine again. Problems may exist within the throttle control,
fuel-injection system or engine, if the engine idle speed will not hold
steady at 1,250 rpm. Contact your local Aprilia service facility for
assistance.
-
6
Stop the engine, once you have obtained a steady 1,250 rpm idle speed.
5/20/2022 6:46:22 AM •
Aprilia...
•
Answered
on May 20, 2022
•
693 views
Will not start Aprilia Mojito Custom
OK< can you provide more details? Does it turn over? Does it fire at all? Do you know if you have a spark? Do you know if fuel is getting through? Has it run properly recently?
To run, a motor needs fuel, air and spark
Inspect all fuel lines and wires. Pull the sparkplug and see if it is burnt/wet/corroded
3/14/2020 6:57:54 AM •
Aprilia...
•
Answered
on Mar 14, 2020
•
262 views
I have installed a new ignition on y aprillia pegaso 2008 and it wont accept the code numbers
It's not the new switch, it's the new keys that have to be programmed.
The keys have uniquely coded chips in them, when you turn on the ECU uses the antenna that is by the ignition switch to look for a code that it recognises, you need to introduce the new key codes to the ECU.
This is what the manual says:
In case of installation of a new ignition switch the procedure is as follows:
Turn ON using new key
The dashboard will not recognise the key and will ask for the customer code: insert the customer code. It is 00000 when supplied. It can be changed to any numeric five digit number.
Now you can enter: MENU, DIAGNOSIS (insert the service code 25973),
Then select MODIFY KEYS and implement the procedure.
If you are not sure about the mode switch, this is what you do:
Use handlebar "mode" switch (left / right) to select "Menu" option on the screen, then press mode switch in to enter.
Use handlebar "mode" switch to select "Diagnosis", press to enter.
Use handlebar "mode" switch to enter the workshop code (25973).
When you have selected the digit you want then press in and it will move to the next digit etc.
You can't screw anything up, if you do it wrong go back or turn off and start again.
2/26/2019 7:27:02 PM •
Aprilia...
•
Answered
on Feb 26, 2019
•
384 views
Not finding what you are looking for?