Question edited for clarity.
Question moved to correct category.
The VRod has an immobilizer. When you disconnect the battery, its memory is lost. Number 1 tip, if you remove the battery, keep power in the system with a battery charger, a battery maintainer, or even a 9 volt MN150 will hold power for 20 minutes. They are very tricky to reset and normally require the dealership! Have a read of this.
https://www.google.com/search?q=2007+harley+davidson+vrod+immobilizer+reset
..
The frame serial number is stamped on the
right side of the frame down tube.
The VIN number label is located just below
the frame number on the right side frame down tube.
The engine serial number is stamped on a pad on the left
side of the crankcase and the right side of the
crankcase. not sure if the VRods are the same.
A website called Motorcycleid.com that offers a variety of parts and accessories for your Harley Davidson, including battery mounts and hardware. I couldn't find the exact size of the bolt that fits the battery box on your 2005 Harley Davidson Lierider. However, you can try contacting Harley Davidson's customer service at 1-800-258-2464 and ask them for the bolt size . They may be able to help you locate the bolt or suggest an alternative
'd1ag' for Diagnostic or Service model.
To enter the diagnostic system and retrieve a trouble code, hold down the trip reset button while turning the ignition from off to on. This will allow you to cycle through the categories, and see which one indicates a code.Feb 9, 2021
just the light says so?"N" will not glow.
or both light N and bike will not push roll>
are brakes looked up, seized.
rolls with clutch pulled in?
ive driving vast motor cycle brands, even old harley 45 flat heads. back to 1963
some I have to jog the bike in gear key out ,clutch not touched.
to get the gears to free up and find neutral
the gear have a thing called dogs. that must un lock
also some bikes
have lots of switches to make a starter work
clutch switch
Neutral
kick stand.
the shifter parts my be a bit rusty
Chopper Bob would have been the best, but says 'Temporarily Close'. I would phone in case it is old COVID data.
https://www.google.com/search?q=Harley+Davidson+mechanic+near+Newark%2C+Ohio
Here are the dealerships in Ohio.
https://www.google.com/search?q=Harley+Davidson+Ohio
You don't say what's wrong, but you may be able to fix it yourself with the help of Fixya and YouTube.
Please always include full 'year make model' in all questions. There are over 10,000 categories including every Harley Davidson model, and most years. I edited your post to add Mr Davidson and put it in the HD generic maker category.
..
Replacing the kickstand on a Harley FXRT requires some disassembly and careful handling. Here are the general steps to replace the kickstand:
Preparation: Ensure you have the necessary tools, a new kickstand, and any replacement parts such as bushings or cotter pins.
Safety precautions: Place the motorcycle on a stable surface and secure it with a stand or by having someone hold it steady. Put on protective gear such as gloves and safety glasses.
Removing the cotter pin: Locate the cotter pin that holds the kickstand in place. It is usually located near the pivot point where the kickstand attaches to the frame. Use pliers or a cotter pin removal tool to remove the cotter pin.
Detaching the kickstand: Once the cotter pin is removed, carefully slide the kickstand out from its mounting bracket. You may need to gently tap it to loosen it if it's stuck. Take note of any bushings or spacers that may be present on the cotter pin side of the kickstand.
Inspecting and replacing parts: Examine the removed kickstand for any damage or wear. If there is a missing bushing or the kickstand is worn, replace it with a new one. Additionally, inspect the mounting bracket and other related parts for any signs of damage or wear. Replace any damaged or worn parts as necessary.
Installing the new kickstand: Insert the new kickstand into the mounting bracket, making sure it aligns properly. If there were bushings or spacers on the cotter pin side, ensure they are in place before inserting the kickstand. Slide it in fully, allowing it to rest in its proper position.
Securing the kickstand: Insert a new cotter pin through the designated hole on the kickstand and frame bracket. Ensure it passes through completely and securely. If necessary, bend the ends of the cotter pin to prevent it from slipping out.
Testing and adjustments: Before fully tightening any bolts, test the kickstand by lowering it and verifying that it extends and retracts smoothly. Make any necessary adjustments to ensure proper operation.
Final steps: Once you are satisfied with the installation and functionality of the new kickstand, reassemble any other components or parts that were removed during the process. Double-check that all fasteners are securely tightened.
It's important to consult the specific service manual or instructions for your Harley FXRT model for detailed guidance. If you are not confident in performing the replacement yourself, it's recommended to seek assistance from a professional motorcycle mechanic.
Question edited for clarity.
Question moved to maker category.
The best idea is to get a Service Manual for it.
https://www.google.com/search?q=1986+harley+davidson+fxr+service+manual
Things like Torque specs can be found on Google by searching 'year make model (the part) bolt torque.
MOTORCYCLE HARLEY PANHEAD or HONDA>? pan European.
? IS NOT A CAR.
WELL IF BATTERY IS GOOD AND STARTER IS GOOD
THE ENGINE IS SEIZED?
ON mc ENGINES WE REMOVE SIDE COVERS AND HAND TURN THE CRANK SHAFT MAKE SURE IT CAN SPIN.
SO WAS PARKED OUTSIDE OUT DOORS FROM MONTHS OF HARD RAIN,IS NEVER GOOD FOR ANY MOTORCYCLE EVER.
OR SHIFT TO 4TH GEAR (1:1 GEAR) AND PUSH Mc TO SEE IF ENGINE IS SEIZED. .
JUMPER CABLE JUMP THE MC BATTER TO A CAR BATTERY.?
CHARGE YOUR BATTERY FOR 4 HOURS OFF A 10AMP CHARGER? LETTING LEAD/ACID BATTERY JUST SIT ASKS FOR Sulfation DAMAGE occurs when a battery is deprived of a full charge, I KEPT ALL MY MC (HAD 5 OR MORE) ON FLOAT CHARGE AND NEVER DID THEY FAIL. FULL TIME PARKED UNUSED.
FUSES GOOD
BATTERY GOOD
STARTER RELAY GOOD
STARTER GOOD
ENGINE NOT SIEZED.
ALSO MANY MOTORCYCLES: this era up.
ALL HAVE NEUTRAL SWITCH STARTER CUT OUT.
SOME HAVE KICK STAND CUT OUT.
SOME HAVE HANDLE BAR DEAD MAN SWITCH LEVERS SET WRONG,
OR CLUTCH SWITCH SAME. CUT OUT.
OR BAD KEY SWITCH OR ANY WIRE TO ANY IF THE ABOVE BAD.
my huge BMW had all that, even in 1977
OR DID YOU MEAN
Honda ST 1100 Pan European????????
IS IT SO HARD TO SAY MAKERS NAME FIRST?
And not put the ST on the wrong end,if true?
but but but !
but is same answer, all motors have the same things , for cranking, (well not my nasty Yamaha' Vargo of old)
starter cutouts on MC are vast, vary by year.
and free manuals for me to read to you never free
pan head or pan European, I fail.
buy the service manual if serious DYI.
see all cutouts and test them all if engine not seized.
use a voltmeter tool , gue$$ing is no fun.