Kymco People S 200 - Answered Questions & Fixed Issues


Hi, Shirley and the usual suspects are:
1. The front wheel or transmission drive unit has failed.
2. The drive unit tab is not properly indexed.
3. Broken speedometer cable.
4. The speedometer has failed.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Speedometer not working
Trouble shooting speedo cable
http://www.49ccscoot.com/manuals/Kymco_People_S_50-200_Service_Manual.pdf
Kymco Scooter Parts
KYMCO People 250 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2009 Kymco... | Answered on Apr 29, 2018 | 181 views


Hi, Barbara for more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Gasket Set Full for 2004 Kymco People 150 eBay
Top End Gaskets Kit Top End Gaskets Kit Athena Aftermarket Division
KYMCO GRAND INK 125 Service Manual
Kymco Scooter Parts ATVs Scooter Parts Performance Scooter Parts...
KYMCO PEOPLE 50 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Kymco... | Answered on Aug 30, 2017 | 33 views


Hi, Dave the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. A failed fuel pump, pressure regulator and or fuel injectors.
16. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
17. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
s200 stalls after 5 10 minutes
GY6 stalls immediately after starting
problems with my Kymco 200 People
http://www.49ccscoot.com/manuals/Kymco_People_S_50-200_Service_Manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2010 Kymco... | Answered on Jun 15, 2016 | 80 views


Hi, Adma despair not all is well too much oil only clogs the breathing system of the engine and causes the tempory sluggish loss of power, always check your engine oil level with the engine at operating tempurature for more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Help overfilled engine oil motorcycles
https://forum.motorcyclenews.com/topic/57129/the-dangers-of-too-much-oil
http://www.fireblades.org/forums/honda-fireblade/103871-worried-have-overfilled-oil.html
http://www.49ccscoot.com/manuals/Kymco_People_S_50-200_Service_Manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Kymco... | Answered on Mar 13, 2016 | 45 views


Hi Hankcycle, for more information about your question please visit the website below. Good luck and have a nice day.
https://absolutelyscooters.net/manuals/Kymco_People_S_50_125_200_Service_Manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Kymco... | Answered on Oct 03, 2015 | 30 views


That depends on the number of participants in 2005.
If you don't give the full problem then we can't give you an answer.

2005 Kymco... | Answered on Sep 11, 2014 | 75 views


THE REASON FOR A HANDLE BAR LOCKING MECHANISM IS TO PREVENT SOME ONE STEELING THE MOTOR CYCLE ALL I CAN SUGGEST IS GET IT DONE AT A MOTOR CYCLE SHOP.

2005 Kymco... | Answered on Oct 19, 2013 | 100 views


In what state?

Kymco People S... | Answered on Oct 02, 2013 | 110 views


check your fuses as well as connections to your coil check your on off switch for power. use a test light for these tests it has to be electrical source related

Kymco People S... | Answered on Sep 04, 2012 | 204 views


u need to read your owners manual, it help me, it can help u to,take the time.

2005 Kymco... | Answered on Aug 29, 2012 | 355 views


battery is low and needs charging most likely.

2005 Kymco... | Answered on May 12, 2012 | 320 views


YES, THIS MODLE HAS A OIL INJECTION AND ANY TWO STROKE OIL WILL WORK BUT TRY AND STAY WITH A MOTOR CYCLE TWO STROKE OIL THERE IS A DIFFERANCE

2005 Kymco... | Answered on May 20, 2011 | 235 views


turn key to on pos then kick it over if no kick start pull left brake or clutch lever in and find start button

2005 Kymco... | Answered on May 10, 2011 | 235 views


pull out the plug and hold it on bare metal too see if youur getting spark.

2005 Kymco... | Answered on Apr 17, 2011 | 87 views


The carburetor is gummed up a bit from petrol evaporating over the past year. Remove the carb and then the float bowl on the bottom of the carb and then clean the carb with spray carb cleaner. Pay extra attention to the float needle area. A generic diagram is below. Please rate my answer. Thanks. tombones49_56.gif

Kymco People S... | Answered on Apr 06, 2011 | 297 views


Under the seat you should find a fuse box with the ignition fuse blown............Hope this helps.

2005 Kymco... | Answered on Jul 28, 2014 | 646 views


The battery may be drained. This is both true for kick start and those with a starter motor. See if you can jump start the bike when you push it and put it in gear. If it starts it is a battery issue.

Kymco People S... | Answered on Apr 05, 2011 | 86 views


You can buy a thread tap at most any good auto parts store or hardware / tool store. The tap will re-thread the existing threads. Bear in mind that if the hole has been stripped out really bad, the integrity of the re-thread is questionable. Having a local machine shop do the re-tap is advised. Alternate to that is just buying a new cylinder head. Please rate my answer. Thanks!
tombones49_14.gif

Kymco People S... | Answered on Mar 26, 2011 | 126 views


Wneh you fit new rings be sure to scour the cylinder bore with a rotary wire brush in the chuck of an electric drill, otherwise the rings won't seat correctly and it may burn oil and lose compression.
Treat as a new engine and run the rings in.

Kymco People S... | Answered on Mar 04, 2011 | 73 views


It should be the negative side of the battery or the frame.
Hope that helps

Kymco People S... | Answered on Feb 17, 2011 | 149 views

Not finding what you are looking for?
Motorcycles Logo

-20 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

84619 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...