2000 Pontiac Grand Am GT Logo
Anonymous
Anonymous Posted on Jul 31, 2011
Answered

I have only 1 car and remote lock< I gave the remote lock to my wife so I could l lock the key in the car when I was done with it. She left town for the weekend and when I went to start the car I got nothing when I tried to start it. When the Key was in the ACC or On position I had full power but when I clicked to start there was nothing thoughts this is for a 2000 Grand AM GT

Answer This Question

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Master 4,803 Answers
  • Posted on Jul 31, 2011
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Oct 10, 2009
Answers
4803
Questions
0
Helped
2962795
Points
18833

Is your security light flashing? If so, your onboard security system has disabled the starter. The security system can be reset (providing you are using the ORIGINAL key for the car) you may have to hook up a battery charger to accomplish this. First hook up the battery charger then when you get in the car, set the parking brake before turning the ignition on. This will keep the daytime running lights from coming on. Then turn the key to the RUN position and wait for the security light to stop flashing. (This takes about 10 minutes.) Then, without turning the key off, turn the key to the START position. The engine should start.

If this doen't work, you will probably have to wait until your wife gets home so you can reset the security system by using the remote to lock the unlock the doors.

I would also recommend investing in a second remote and key so you don't have this problem in the future. The second key and remote is pretty easy to progrm on your vehicle. This can be done either by the dealer or most aftermarket repair shops. You MAY even want to try to do it yourself. Instructions for programming additional keys and remotes are located in your Owner's Manual.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I program a new key fob into my Chevrolet HHR LT
Turn the key "ON" "OFF" "ON" "OFF" "ON" "OFF" "ON" and leave in the "ON" position. Press and hold both the lock and unlock buttons on the remote until the doors lock and unlock. Turn the key "OFF" and your remote should be programmed. If this doesn't work, you might have to take your vehicle into the dealership.
Read full answer
Jul 10, 2015 • 2007 Chevrolet Chevrolet HHR LT
1helpful
1answer

Manually oped door lock on2004 deville from open window now won&#39;t srart with out waiting a couple minutes
You triggered the security system on this model, which is notoriously sensitive, and the security shut down the ignition. Don't push your luck, use the key fob to unlock or you may wind up with a locked down and inoperable Cadillac.
Read full answer
Dec 17, 2014 • 2004 Cadillac Deville
0helpful
1answer

Town car keyless entry
Silly question, have you tried to replace the battery in the remote? Sounds like it's getting weaker and weaker. worth a shot.
Read full answer
Mar 18, 2014 • Cars & Trucks
0helpful
1answer

I need to change my door codes on my 92 nissan maxima
1991-94 Nissan Maxima key less entry reprogramming:

1. The *original code found on the gold box under the glove compartment by the left kicker panel
(there should be 3 sets of codes on the gold box the code u want begins with the letter F and has 7 digits.) (_EXAMPLE_ F# S1234567 )

2. Close and lock all of the doors,
enter the 7 digit code ( make sure you have your key in your pocket not inside any key hole).

3. Once the code is entered correctly you will hear a long beep.
While the beep is sounding ... ENTER your NEW 4 digit code, (you will then hear random beeps)
>>>>>>>>>>>>>Do not touch anything until the beeping stops.
________After the beep is over______
4. Type: S or ST (Clear) and the New 4 digit code and the door will open automatically.
~~~~~~~> NOW YOUR DONE YOUR CODE HAS BEEN RESET.
5. If you forget your new code. Just enter the original one and start all over.
Its really simple I hope it helps...............
Read full answer
Mar 21, 2011 • 1993 Nissan Maxima
0helpful
1answer

I have a 2003 Town and Country and my son randomly pushed buttons on my key remote and now has triggered an automatic lock code. When I unlock van using the key remote, it beeps every minute for 3 times...
you cant ,dealer only from 2005 onwards to reset the remote ,another dealer con job
Read full answer
Oct 30, 2010 • 2005 Chrysler Town & Country
4helpful
1answer

Remote key fob won'tprogram
1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works
Read full answer
Aug 13, 2009 • 1999 Ford Escort
2helpful
2answers

2007 Lincoln Mark LT Key Fob
Theres only 1 way to tell if it will work - try it :)

Here is the procedure to marry a new remote to your truck.

1. Close all doors and then open drivers door and press the UNLOCK
button on drivers door panel while door is open and insert key in ignition.
2. Turn ignition from OFF to RUN (not start) 8 times within 10 seconds, with the
8th time ending in RUN. Door locks will cycle to confirm programming
mode.
3. Within 20 seconds press any button on first keyless remote.
Door locks will cycle to confirm programming.
4. Within 20 seconds, press any button on second keyless remote.
Door locks will cycle again to confirm programming.
5. Turn ignition to OFF.
Locks will again cycle to indicate end of programming mode.


Both the Escape and LT program the same - the transponder should have the same resistance.


Try it out!!


Thanks for using FixYa - a Very Helpful Rating is appreciated for answering your FREE question.


Read full answer
Aug 04, 2009 • 2007 Lincoln Mark LT 4x2 5.5
2helpful
1answer

Sliding door will not lock or unlock with remote key or front door panels
I have the same van and the passenger side sliding door stopped locking by the remote or the electrical switch. I took the door panel off for the sliding door and located the door lock solenoid( the locking solenoid was bad). but it was sOOOOOO dificult to remove the door lock solenoid ( and I thought I had every tool) that I had no choice but to put it all back together and tell the wife she needed to take it to the dealership to fix it. I forget how much the part was but the dealer part was suprisingly more expensive than I thought it would be.
Read full answer
Jun 10, 2009 • 2006 Chrysler Town & Country
0helpful
2answers

The ABS light and Trac off light is on, what's wrong?
There are sensors mounted behind the front wheels. Look for two small wires, running in plastic line protectors,behind each of the front wheels. There is a small connector plug that attaches to the sensors. These can get dirty and cause the problem you have. Cleaning them and using a dielectric grease might solve the problem. I have seen these get unplugged when brakes get worked on or even, on occasion, when tires get changed.

I have also seen the wires get torn apart along the undercarriage. You might want to follow them back to the main harness looking for damage.

In both circumstances you are going to want to get the car up in the air, with the tires removed and on sturdy jack stands.So you can get a clear view and have room to make any needed repair. You don't want to do this with car on it's tires.

Good Luck!
Izatech
Read full answer
Apr 13, 2009 • 2000 Pontiac Grand Am GT
2helpful
1answer

Automatic door locks will not work.
you need to take it to the dealer and have them check the bcm for codes.... also have them check to be sure you have the latest software in the bcm.. its possible that you just need a software update... there are several TSB's covering the concern you have..... it can be a very simple fix with software or even a stuck lock switch may need to be replaced... without the proper diagnostic codes being read from the bcm all that can be done is guessing..and that can be expensive...
Read full answer
Feb 02, 2009 • 2005 Chrysler Town & Country
Not finding what you are looking for?

View Most Popular

2000 Grand Am GT

  • Cars & Trucks

Related Question

How do I program a new key fob into my Chevrolet HHR LT

  • 2007 Chevrolet Chevrolet HHR LT

Related Topics

343 views

Ask a Question

Usually answered in minutes!

Popular Questions

How do you check/add transmission fluid to a 2004

2004 Pontiac Grand Am

Looking for a 2.2 ecotec timing chain diagram with

2002 Pontiac Grand Am

1999 Pontiac Grand Am Overheating

1999 Pontiac Grand Am GT

Electric sunroof stuck open can it be closed

2001 Pontiac Grand Am SE

How many quarts of transmission fluid does it hold

2001 Pontiac Grand Am SE

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Pontiac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...