How do you change the fuel pump? is there a access panel and if so where is it located?

Removal & Installation
To Remove:

1. Before servicing the vehicle, refer to the precautions at the beginning of
   this section.
   
2. Release fuel pressure.
   
3. Remove or disconnect the following:
   
   
   
   • The rear seat
     
     
     
     
     
     Electrical Connector
     
     
     
     
     
   • The fuel pump electrical connector
     
     
     
     
     
     Battery Cable
     
     
     
     
     
   • Battery cable
   
   
4. Raise and safely support the vehicle
   
5. Remove or disconnect the following:
   
   
   
   
   
   Fuel Tank Drain
   
   
   
   
   
   
   
   • Fuel from fuel tank
     
     Stabilizer Bar
     
     
     
     
     
     Stabilizer Bar and EVAP Canister
     
     
     
     
     
   • The rear stabilizhow do you change the fuel pump? is there a access - dod_intrpd_filler_tube.gif
     
   • Stabilizer bar toward rear of vehicle
     
     
     
     
     
     Fuel Filler Tube
     
     
     
     
     
   • The fuel filler tube from fuel tank
     
     
     
     
     
     Fuel And EVAP Lines
     
     
     
     
     
   • Fuel and EVAP lines
   
   
6. Position transmission jack under fuel tank assembly.
   
7. Remove fuel tank straps bolts passenger side first.
   
8. Lower fuel tank and remove the purge line and vent line.
   
9. Disconnect fuel line from fuel pump module by depressing quick connect
   retainers with thumb and fore finger.
   
10. Slide fuel pump module electrical connector lock to how do you change the fuel pump? is there a access - dod_intrpd_fuel_tank_tool__nut.gifisconnect the electrical connection from the fuel pump module, by pushing
    down on connector retainer and pulling connector off of module.
    
    
    
    
    
    Fuel Tank Locknut
    
    
    
    
    
11. Use Special Tool # 6856 to remove fuel pump module locknut.
    

1. Wipe seal area of tank clean and place a new seal in position in the tank
   opening.
   
   
   
   
   
   Fuel Tank Locator
   
   
   
   
   
2. Position fuel pump in the tank.
   
   
   
   • Make sure the alignment tabs on the underside of the fuel pump module flange
     sits in the notches on the fuel tank.
   
   
3. Position the locknut over the fuel pump module.
   
4. Tighten the locknut using Special Tool # 6856
   
   
   
   • Torque to: 40.5 ft. lbs. (55 Nm)
   
   CAUTION
   Over tightening the pump lock ring may
   result in a leak.
   
   
5. Position the fuel tank on the transmission stand.
   
6. Install or connect the following:
   
   
   
   • Fuel pump electrical connector into hole in the body
     
   • The purge and vent lines
     
   • Fuel tank and tank straps
     
   • The fuel filler tube and tighten the clamp
     
   • The stabilizer bar and install bolts
   
   
7. Lower vehicle.
   
8. Install or connect the following:
   
   The fuel pump electrical connector that is ihow do you change the fuel pump? is there a access - next.gifar seat
   
   • The rear seat
     
   • The battery cable
   
   
9. Fill fuel tank.
   
10. Use the DRB or equivalent scan tool to pressurize the fuel system.
    
11. Check for leaks.

Most Chrysler Concord s have acsess panels located in trunk.