P1443 1. failed evap pressure sensor 2. blocked hose between purge valve and ftp sensor 3. evap purge valve stuck closed what would be the best guess1996 ford thunder bird v8

https://garatos.com/p1443-ford-code/

DTC P0497: Evaporative Emission (EVAP) System No Flow During Purge
Circuit/System Description
The control module tests the evaporative emission (EVAP) system for a large leak, or a stuck closed EVAP canister purge valve. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge valve OPEN and the EVAP vent valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level increases too slowly, a DTC sets.

Diagnostic Aids
• A loose, missing, or damaged fuel fill cap can cause this DTC to set.
• A stuck closed, blocked, or restricted EVAP canister purge solenoid valve, can cause this DTC to set.
• A blockage or restriction in the EVAP canister purge solenoid valve vacuum supply hose, EVAP canister purge solenoid valve purge pipe, EVAP canister, or vapor pipe, can cause this DTC to set.
• A temporary blockage in the EVAP canister purge solenoid valve, purge pipe or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.
• To help locate intermittent leaks, use the J 41413-200 Evaporative Emissions System Tester (EEST) to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT High Intensity White Light. Introducing smoke in 15 second intervals will allow less pressure into the EVAP system. When the system is less pressurized, the smoke will sometimes escape in a more condensed manner.
• To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT .
• Observe the Freeze Frame/Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set. This may assist in diagnosing the condition.

simple bro :)

check these its one of these go by one by one

Faulty EVAP Pressure Sensor EVAP Pressure Sensor harness is open or shorted EVAP Pressure Sensor circuit poor electrical connection Blocked hose between purge valve and FTP sensor EVAP purge valve stuck closed

DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.

?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.

?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .

?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system

Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

1. Install the fuel cap.
2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.

?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.

If

code p1443 - Evap canister purge system mafunction.possible cause faulty Evap canister purge valve.fuel vapor hose blocked between Evap purge valve and the FTP sensor or blocked between purge valve and intake manifold or vacuum hose blocked between purge valve and intake manifold.code po430 catalytic system efficiency bank 2 below threshold.possible causes. air leaks at the exhaust manifold or in the exhaust pipes. catalytic converter is damaged.ECT OR CHT SENSOR has lost its calibration.engine cylinders misfiring or the ignition timing off.engine oil is contaminated.front HO2S or rear HO2S is contaminated with fuel or moisture.both front HO2S OR REAR HO2S is loose in mounted hole. fuel pressure is too high due to faulty fuel pressure regulator.

PCV valve would have nothing to do with it !
P1443 - Very Small Or No Purge Flow Condition A fuel tank pressure change greater than a minus (-) 7 inches of H 2 O in 30 seconds has occurred with purge (fuel vapor) flow less than 0.02 pounds per minute.

• Blocked fuel vapor hose between EVAP canister purge valve and FTP sensor.
• Blocked fuel vapor hose between EVAP canister purge valve and engine intake manifold.
• Blocked vacuum hose between EVAP canister purge valve-solenoid and engine intake manifold.
• EVAP canister purge valve stuck closed (mechanically).

Check for blockages between the fuel tank, EVAP canister purge valve and engine intake manifold. Check obstructions in the EVAP canister purge valve diaphragm and ports.
Suggest you buy a repair manual if you want to try an fix yourself .Or Go to ford web site Ford Oem1stop com an pay 29 bucks for 72 hours for repair info . Or take it to a qualified repair shop an have it smoke tested . Or goolge purge valve for a pic. an see if you can find it under the hood .

CODE P1443 - LOW PURGE FLOW OR NO PURGE FLOW CONDITION DETECTED.POSSIBLE CAUSES EVAP CANISTER PURGE VALVE STUCK CLOSED MECHANICALLY FUEL VAPOR HOSE BLOCKED BETWEEN EVAP PURGE VALVE AND THE FTP SENSOR OR BLOCKED BETWEEN PURGE VALVE AND INTAKE MANIFOLD OR VACUUM HOSE BLOCKED BETWEEN PURGE VALVE AND INTAKE MANIFOLD.CANT GIVE PRICE CHECK UNTIL FIND OUT THE PROBLEM.

P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:

Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.

Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.

Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.

EVAP canister purge valve stuck closed (mechanically).

Possible Solution:
Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

The canister is on the passengers side near the firewall if I recall correctly.

Here is what I could find for your code error as potential causes:
After market parts and accessories nonconforming to the EVAP system specifications.
Damaged, missing or improperly installed fuel filler cap.
Blockage in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube) in EVAP system.
Disconnected or cracked fuel vapor hoses/tubes in EVAP system.
EVAP canister purge valve stuck closed.
Canister vent (CV) solenoid stuck open.
Fuel tank pressure (FTP) sensor malfunction.
EVAP canister leaking.
Fuel vapor control valve tube assembly blocked.
Fuel vapor vent valve assembly blocked.

Obviously the gas cap would be the easiest and cheapest thing to fix.  Just make sure it is put on correctly and tight.  If it is not that, I would have to suggest to take it to a mechanic because the other problems on that list are not really DIY material.  Hopefully it is the gas cap and you can take care of it yourself.  Good luck.

Ok i have the same make and model car.And had same problem but i was only needing new hoses. thwe code reader will not tell you if they are bad you just have to check this. The purge valve and canister is located under hood on passenger side behind bumper. look behind the light through the openings. You have to raise car up and do the repairs from under the bottom of the bumper.On passenger side under hood above the wheel fender and between the engine you will see a emmision line about the size of a pencil leads to the purge valve. the valve cost about $18.00 and canister cost around $75.00 at auto zone. The canister is the square box and sometimes you can take apart and clean it and put back together and it should work fine.