At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Turned on the car with windshield covered with snow,
did not realized that wipers were on.
After removing the snow tried several times but wipers are dead
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
sounds like the linkage came unhooked under the hood. Sometimes you can just pop it back on other times if its broke you will have to install a new linkage.
With ya'lls perty white heavy snow,it made your wipers get unaligned,you will have to remove and reset.It's not good to remove snow from wipers when windshield is loaded,get a scraper or blower and go at it.Wish we got snow.
The windshield wiper circuit has an circuit breaker in it, under heavy load this breaker trips to protect the wiper motor, when the motor cools, the breaker resets automatically restoring proper wiper action.
Hello: lift/remove cover from the lower end of the w/w arm (toward bottom of windshield) there should be a 13mm nut that attaches the arm to the transmission shaft. Use a 13mm box end and see if the nut is tight. If not tight position the arm in the proper position and tighten nut, re-install nut cover.
Does the wiper motor run? If you can hear the wiper motor run, the wipers arms may have disconnected from the wiper motor,you will have to remove the wiper arms,and the plastic cover to access the wiper motor,and check for damaged parts.If your wiper motor does nothing at all, you probably blew a fuse do to the resistance on the arms,refer to your owners guide for fuse panel, and fuse locations. hope this helps
The problem could be a bent parking pall bracket. This is usually caused when you wipe snow from windshield using the wipers instead of brushing off. You need to remove both wipers and the cover from the drivers side. Remove the cover over the wiper motor assembly (held by a plastic button). On the right side of the wiper mechanism is a small tab (part of the wiper bracket). This tab needs to be straight for the wiper park pall to rest against.Carefully hammer this tab straight (or you may have to replace bracket, big job) Then cycle the wiper and you will see the assembly return to park position. Re-install all parts in reverse order.
Hope this works for you.
I just solved this problem last night with my '05 Impala, and ultimately the solution was what newton5083 stated above. Yet, it may also be this (I found it online somewhere):
You have bent or broken the "park tab" on the windshield wiper motor bracket. The correct way to fix this is to remove the wiper arms, wiper linkage and wiper motor from the wiper motor bracket, and install a new bracket. I just bent the tab back into place a couple times for our daughters 2005 Impala but it kept getting bent down again when they didn't take the time to make sure the wipers were not frozen to the windshield, or tried running the wipers to remove heavy snow on the windshield. So yesterday I fabricated a small piece of metal and bolted that to the bracket in the same place the tab stop was. If someone wants to access this bracket and tab- 1. Use a ½ inch or 13mm socket & ratchet or wrench to remove nuts on wiper arms. 2. They may make a special tool to remove the arms, I used a screwdriver and hammer to tap bottom of the arm to wedge them apart from the spindle. 3. Two small button-looking clips hold the drivers side cowl cover in place under the windshield. These are two-piece clips, pry up the center, than the outer piece. 4. Unclip the washer hose from cowl cover, than pull out plastic cover. 5. There is a smaller plastic cover with on plastic button head holding that cover in place. Gently pry under that clip to remove that cover. 6. Now you can see the wiper trans and bracket. You should see a small tab on that bracket that looks pushed down and bent or possible a square small hole with some torn off metal where the tab broke off. 7. Remove small plastic cover over the wiper transmission and you can see a small spring-loaded arm underneath the wiper transmission assembly. 8. You need to find something to pry that tab back up so when the wipers are running that spring loaded little arm just snaps past the tab running clockwise. It's when you shut off the wipers that the wiper transmission assembly reverses rotation counter clockwise and the small spring loaded arm underneath hits that tab stop, than the wipers will go all the way down and shut off as they should. Once that tab stop gets bent out of the way the little spring loaded arm has nothing to stop the wiper transmission assembly so it keeps traveling counter clockwise until some other stop shuts the wipers off straight up on the windshield.
There is a revised bracket part # which is supposed to be more durable, GM part #12368639. Here is a copy of the TSB which points out this problem: Bulletin No.: 05-08-43-003A Date: March 10, 2005 TECHNICAL Subject: Windshield Wipers Park in Up Position (Replace Windshield Wiper Motor Bracket) Models: 2005 Chevrolet Impala, Monte Carlo Supercede: This bulletin is being revised to make a correction to the Parts Information. Please discard Corporate Bulletin Number 05-08-43-003 (Section 08-Body and Accessories).
Condition Some customers may comment that the windshield wipers park in the out wipe (vertical) position. Cause This condition may be caused by a bent park tab on the windshield wiper motor bracket.
Correction To correct this condition, replace the wiper motor bracket. It will be necessary to transfer the following parts listed below to the new bracket. ^ Wiper transmission ^ Wiper motor crank arm ^ Wiper motor 1. Remove the windshield wiper motor drive system module. 2. Remove the windshield wiper transmission from the windshield wiper motor bracket. 3. Remove the wiper motor crank arm from the windshield wiper motor. 4. Remove the windshield wiper motor from the bracket. 5. Install the windshield wiper motor to the new bracket. 6. Install the wiper motor crank arm to the windshield wiper motor. 7. Install the windshield wiper transmission to the windshield wiper motor bracket. 8. Install the windshield wiper motor drive system module.
A TSB is not a recall, if vehicle is still under warranty the dealer should be repaired for free. If not, you'll have to pay for the repairs.
×