At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Undo the bolts around the window winder handle and any other bolts holding the winder, make sure the glass does not fall and brake, then slide the winder out,
The bolts that hold the motor for window loosen up and fall out .but before it falls completely out it will gouge out the door frame find the bolts in the bottom add a washer lock tight the bolt and tighten them back in easier to do 1 at a time this happens on all doors
one screw at handle two on arm rest or under switch the rest is plastic retainers just putt and use trim tool or screw driver two bolts hold glass to regulator have to lower window till you see then remove remove bolt that holds front track and slide glass in top and put in track front an back set in regulator and bolt in raise then bolt front track
its a crank shaft pulley bolt if its broke off flush you cannot drive it any where cause if you do the pulley will fall off and then your engine is scrap so if you can make the room you need in front remove rad belts pulley and so on if your a good machanic now at the crank with the pulley off you might see the end of the bolt try to take a small punch and try to tap on it slowly without damage more it might turn if not you have to drill a hole in the center and then try to put in a easyout tool to remove broken stud if not you can call a mobile welder to come and weld a nut or bolt on the shaft to remove it no torches electric there are seals and rubber belts inside the cover i all else fails call a garage and tell them to give an estimate how long it will take because it can be a long job and exspensive
You will have to remove the driver side door panel. Tape the top of your glass to the door so it wont fall and break. Remove the bolts and harness' going to the regulator. And reverse for installation.
probably need a new window regulator. ebay. 93 to 98 should fit.
Section 01-05: Trim, Interior
1998 Villager Workshop Manual
REMOVAL AND INSTALLATION
Trim Panel(s), Door
Front Removal
Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
Pull the shop rag back and forth to release the window regulator handle clip.
Remove the three cover caps and front door trim panel screws.
Remove the one front door trim panel capped screws from the door pull handle.
If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power
Front Door Removal
Disconnect the battery ground cable (14301) .
Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
Remove the two front door brace bolts and the front door brace.
Disconnect the front window regulator electric drive electrical connector.
Remove the four front door window glass regulator track bolts.
Remove the three front window regulator electric drive bolts.
Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
I am guessing that you have the door panel off already so take the window all the way up and take some duct tape and secure the window up all the way. Remove the front door window glass to regulator assembly bolts. Loosen the glass clamp fasteners through the 2 vertical slots in the inner door panel. To install tighten to 80 inch pounds. If equipped disconnect the front door window electrical connector. Remove the front door window regulator bolts to install tighten to 8 foot pounds. Remove the front door window regulator and motor. To install in reverse order.
×