How can i disable passanger air bag on 1999 z3

640results for 1999 dodge ram air bag

More than likely, since the wiring for the passenger side air bag is located right where you were working, you may have disconnected a wire. Start by wriggling the plug in to the air bag.

Yes!!! You can replace it yourself.(Dont let others fool you into paying extra or telling you otherwise.)
-This is for pontiac grand ams 1999-2005 only.
-There are no frontal airbag impact sensors nor are there belt tensioners.
-The SRS system consists of only the (driver airbag) ,(passanger airbag),and the (airbag control module) in 1999-2005 grand ams.

If you crash/wrecked and airbags deployed you will need.
-Driver and Passanger airbags
-Airbag control module

You can buy cheap airbags from a local junkyard any year from 1999-2005 will fit.
You can also find an airbag control module for cheap at your local junk yard BUT YOU MUST FIND ONE WITH THE SAME (PART NO.) AND (SERV NO.) AS THE ONE YOUR REPLACING.The (part no.) and (serv no.) should be at top left of airbag control module.However it does (Not) have to match numbers under barcode or the numbers at the far bottom right of airbag control module.

After you get both airbags and airbag module
-Disconnect car Battery
-Replace airbags
-Replace airbag module (under passanger seat)
-Double check all connections and connect battery.

Congradulations!Your airbags should be back online.

Notes: Two torx 35 head screws hold the driver airbag, access is through two holes behind steering column.
To remove passanger airbag you have to remove glovebox it uses (7mm)screws.After you remove you will see a pair of (10mm)screws holding airbag.
To remove airbag control module First remove passanger seat 2(15mm).Then after removing you will notice a raises area kinda like a vertical bump.Take a razor blade to your carpet and cut it to explose the module underneath.
The airbag module is held by three screws depending on the year of your car it varies.Most likely 3 (10mm).

Hi Edward your problem is probably the occupancy detector which is located in the passanger side front seat base.Its function is to detect wheather or not there is a passanger in the car.It will not allow the passanger air bag to deploy in the event of an accident if there is no passanger present.Unfortunately it cannot be repaired and will have to be replaced to do this remove the seat abd remove the seat cover and padding,[the detector is located in the seat base.
I would recommend that the air bag system is scanned to find out the fault before you buy a new detector.

Could be several causes... but the result is consistent - when the light is on the air bag is disabled

The motion sensor board has a failure - or one of the crash sensors has failed - so the motions sensor board is not receiving the desired signal. To prevent an accidential firing of the bag, the system disables the airbag and turns on the light....

remove the fuse 4 the passenger airbag

That means your air bag is disabled and will not deploy in an accident. Only have a certified tech work on an air bag.

no you can't there is not a switch to turn of airbag like some manufacturers.

There must be a problem with the air bag system for the light to be on, if the system was o.k. the light would be off and have a stored code. You cannot reset this light with a generic obd2 scanner. You need to access the air bag system and read what codes it has stored. Good Luck.

as long as the srs light is not on the srs system is functioning properly. There is a passanger seat recognition senser and some vehicles are equiped with baby smart-which disables the passanger front air bag when a mercedes child seat is placed on the passanger front seat. More than likley the airbag is being manually switched off. there should be a place on the dash or center console to place the mechanical part of your smart key into and turn the air bag on or off.Once the system is reactivated clear the message in the cluster or turn off your ignition and remove the key and then reinsert key and turn on-this should clear the memmory of the cluster and your message center should not display any warnings