What is the torque specs for a 2007 ford freestyle intake manifold bolts/ spark plugs and coil hold down bolts

The 2014 Chevy Spark intake manifold torque sequence and torque specs depend on the engine type. Here are the torque specs and sequence for each engine type:
1.0L Engine:

• Step 1: Tighten the bolts to 44 inch-pounds (5 Nm).
• Step 2: Tighten the bolts to 89 inch-pounds (10 Nm).
• Step 3: Tighten the bolts to 18 lb-ft (25 Nm).

Torque sequence: 8 4 1 5 9 7 3 2 6 10
1.2L Engine:

• Step 1: Tighten the bolts to 44 inch-pounds (5 Nm).
• Step 2: Tighten the bolts to 89 inch-pounds (10 Nm).
• Step 3: Tighten the bolts to 18 lb-ft (25 Nm).

Torque sequence: 8 4 1 5 9 7 3 2 6 10
It's important to follow the torque sequence and torque specs carefully to ensure that the intake manifold is properly secured and sealed. Over-tightening or under-tightening the bolts can cause leaks or damage to the engine.

XC-70 (typo) YES.
ALL CARS MADE, FOR SURE LAST 20 YEAR.
HAVE FULL SERVICE MANUAL THAT COVER ALL THAT AND 1ZILLION MORE TOPICS. ALL DO
older cars too, but are weaker before manuals were in digital form.
for sure 2007!
you posted with not country,
and what engines is actually there.
ours USA is. 2.5L L5 engine and 2.4L
has x6---- O-RINGS here.
in, inch/lbs, Divide by 12 to get foot/lbs


a diagram what? a VC?
not sure what that means , and all that is in the SM service manual.
CAN I ASSUME, you need all 10 steps in the manual told to you?>

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove intake manifold. Refer to Intake Manifold removal and installation.
3. Remove spark plugs from:
   • Cylinders 1 and 5-5-cylinder engine
   • Cylinders 2 and 5-6-cylinder engine
4. Install two camshaft cover press tools 999 5454 into the vacated spark plug holes. Ensure that the bolt in the spark plug well is fully tightened 22 ft. lbs. (30 Nm).
5. Remove Variable Valve Timing (VVT) solenoid.
6. Leave a 0.079-0.118 inch (2-3mm) gap to the camshaft cover when installing the press tools 999 5454
7. Remove all bolts securing the camshaft cover to cylinder head.
8. Use pliers 999 5670 to lift camshaft cover from cylinder head.
   
   • Install pliers at the stop lugs. Start with cylinder 1 and work alternately backwards.
   • Slacken off the wing nuts approximately 2 turns.
9. 
   
   • Repeat the procedure working toward rear of engine.
   • Carefully press out the front and rear camshaft seals.
   • Remove the two press tools 999 5454 from spark plug holes.
   • Remove the camshaft cover.

that?
the install is more complex , including sealants.
and
tighten the bolts in sequence from the center and outwards to 88 inch lbs. (10 Nm).
and

1. Install:
   • Variable valve timing (VVT) solenoid. Use a new gasket. Tighten center bolt to 89 ft. lbs. (120 Nm), center plug to 26 ft. lbs. (35 Nm)
   • Spark plugs and tighten to 22 ft. lbs. (30 Nm)
   • Intake Manifold, refer to Intake Manifold removal and installation

and more, read the manual.

RTM
https://eautorepair.net/Marketing/Default.asp





.

Question edited for clarity.

6 to 8 ft lbs. It is so little is is measured in INCH pounds. 72 in/lbs is the torque, which equates to 6 ft/lbs.

2015 Dodge Journey 3.6L Engine Torque Specs

dodge-specs.com https://dodge-specs.com > cars > 2015 > journey3.6

The intake manifold bolts can be torqued down to 8 ft-lbs regardless as to whether it is the lower or upper manifold. The ignition coil assembly can be torque ..

..

Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

they are in the factory repair manual.

copy and paste
https://www.justanswer.com/ford/2w39p-need-upper-lower-intake-manifold-bolt-torque-specs.html

https://www.justanswer.com/ford/1vuu6-need-lower-intake-torque-specs-2001-ford-windstar.html

You actually do see them you just don't realize it. When you look at the motor from the top down you should see what looks like caps with wires running to them evenly spaced across both cylinders. You ahve to remove the retaining screw and then pull those up. Those are actually the independent coils that ford uses on top of each spark plug. You'll need a socket and extension to reach the plug itself, also, if you have the 6 cylinder motor you'll have to remove the upper intake in order to reach the the plugs nearest the firewall. On there were 6 retaining bolts for that I'm not sure about the 2003 because of design changes. You don't want to remove the intake manifold itself, just the top half of the intake itself.

Need to remove upper intake manifold to reach valve cover close to firewall.
1) The location of spark plugs 456 are under the plastic shield in front of the engine. It takes an 8mm socket to remove the three bolts holding the shield once the shield is removed you will see a coil for each spark plug. Use the 8mm socket and remove the coil and rubber boots. You will now see the spark plug (note there are not any spark plug wires).
2) The location of spark plugs 123 are located to the rear of the eng. You have to remove the air intake manifold in order to get to the spark plus. Remove the throttle wire then remove the other items on top of the intake manifold.