Can i program a keyless entry remote key fob clicker transmitter for my 2005 chrysler sebring myself

Looking at the service info for your Uplander, it has Remote Control Door Lock Receiver technology, so keyless entry should work if you have a capable key fob.

Your Uplander will need the key fob programmed by a service center or dealer with the technology to program those GM vehicles that can't be done manually (i.e. Tech 2 scan tool).

Dealer ! Unless you have a factory or professional scan tool .

Transmitter Programming
Important: Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
Important: All key fobs must be programmed each time any one fob is programmed. The scan tool must stay connected until all of the transmitters are programmed.
Install a scan tool and navigate to the BCM Module Setup menu.
Select Program Key Fobs.
Follow the scan tool on-screen directions.
When the programming operations have completed, operate the transmitter functions to verify correct system operation.

The keyless entry system consists of the following components:

• driver door module (DDM)
• keyless entry transmitter
• keyless entry keypad

The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).

• Battery junction box (BJB) fuses:
  • circuit breaker 7 (20A)
• Central junction box (CJB)
  • 4 (10A)
  • 6 (15A)
  • 8 (25A)
  • 13 (5A)
• Keyless entry keypad switch
• Power door lock actuator
• Luggage compartment release switch
• Luggage compartment release solenoid
• Connectors or connections
• Wiring harness
• If fuse's good have checked for DTC'S - diagnostic trouble codes .
• B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .

• The doors do not lock/unlock using the remote transmitter

• Remote transmitter not programmed.
• Remote transmitter.
• DDM.

• Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.

1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.

1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.

1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Programming a Replacement Keyless Entry Remote ' Filear ...

filear.com/?p=131

Oct 17, 2012 - If the transmitters don't work, or if you'd rather not match the transmitters yourself, .... Tried these instructions last night on my 2005 Grand Prix.

Key FOB Not Working - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.../11859-Key-FOB-Not-Working

Mar 15, 2009 - 10 posts - ‎3 authors
Hi Everyone, One of my Key FOB's stopped working. Is there a way of ... Well, to be honest, you don't know where that FOB has been? LOL ... 2009 Dodge Grand CaravanSXT (3.8L), Light Sandstone Metallic, 125K miles 2005 Volvo .... By jimmy154 in forum 3rd Generation Chrysler Minivans: 1996-2000.

Key May Not Start Car or Release From Ignition : Dodge ...

repairpal.com > Problems > Dodge > Grand Caravan

Dodge Grand Caravan Key May Not Start Car or Release From Ignition. ... If the newkey doesn't work, replacing the lock cylinder including tumblers ... I am able to turn off the van, but the key is stuck in the ACC position, draining my battery. ... In reading other comments, I see it may be the FOB so I'll carry both with me and ...

2009 Dodge Grand Caravan car lock doors not working

Search Results

2004 Mitsubishi Endeavor Key Fob Remote Programming ...

blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

Mitsubishi - Free Keyless Remote Fob Entry programming .

How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

? 2:04
www.youtube.com/watch?v=yeQRdre7O0Q
Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

key fob dead, a factory key ?????
first off what country are you in, there are vast sub models of LC sold
the world over, (complex to the extreme)
goggle finds this...
http://www.remotesunlimited.com/blog/1994-toyota-land-cruiser-keyless-entry-remote/

say it might be port of entry installed,so what port, USA?
here is one brand
http://www.remotesremotes.com/1994-Toyota-Land-Cruiser-Keyless-Remote-Key-Fob-Clicker-s/6063.htm

you will need to identify which keyless system is in your car.
then google for that. and you will find it.


got a 70 series LC, or> 80 series?
see em all here, huge variances.
http://en.wikipedia.org/wiki/Toyota_Land_Cruiser

TRANSMITTER PROGRAMMING
IMPORTANT: All transmitters which are to be recognized by the remote control door
lock receiver (RCDLR) must be programmed in a single programming
sequence. If the system is placed in program mode it will erase all
previously programmed transmitters upon the receipt of the
programming signal from the first transmitter. Up to 4 transmitters can
be programmed. Do not operate or program the transmitters in the
vicinity of other vehicles that are in the keyless entry program mode.
This prevents the programming of the transmitters to the incorrect
vehicle.
Install 1. a scan tool.
Use the scan tool in order to access the Body Control Module (BCM) Special Function or
Module Setup: Program Key Fobs.
2.
3. Press the START soft key on the scan tool.
IMPORTANT: The scan tool must stay connected until all of the transmitters are
programmed.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter.
After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
4.
5. Repeat the previous step in order to program up to 4 transmitters.
6. Remove the scan tool.
7. Operate the transmitter functions in order to verify correct system operation.

Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the DOOR unlock switch.
4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct system operation

This is what i found but you need one fob.

here is another way if you can get it done( i bevlieve) There is a box under the dash of your can it says keyless entry if you have the right box and the fab just plug and play.

Make sure you get the screws in the defrost vent there is some screws and then it there is snaps


http://shopping.msn.com/specs/keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor/itemid1124228415/?itemtext=itemname:keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor

goto your local Chrysler dealer silly!