Hi there! Would you know where on a 2007 Audi S6 is the Keyless Entry/Start Module located. P/N 4F0-907-335-7 - Thanks!

NO FOBS DETECTED
Refer to Keyless Entry System Description and Operation

Keyless Entry System Description and Operation - Passive
Passive keyless entry allows entry to a locked vehicle without pressing any buttons on the keyless entry transmitter. You must only have the transmitter with you. This passive system is also part of the vehicle starting system. It allows you to start and run the vehicle having only the transmitter as your key. The passive entry and starting system use low frequency antennas in 4 different areas on the vehicle to determine the location of the transmitter. When passively opening a locked door or the rear compartment lid, you must have a programmed transmitter with you in your pocket, purse, or briefcase. As a customer opens the door handle or presses rear compartment touch pad, the low frequency antenna sends out a challenge to the keyless entry transmitter. The transmitter must be in a one meter range of the door or rear compartment lid in order to receive the challenge. If the challenge is met, the transmitter will respond, allowing the door to be unlocked and opened. Passive entry allows you to operate the following features:
• Passive door unlock/unlatch
• Passive rear compartment lid release
• Illuminated entry lamps
• Vehicle starting
The keyless entry system has the following components:
• Keyless entry transmitters
• LH and RH door antennas (part of the door handle assembly)
• Rear compartment antenna
• Console passive antenna
• Console active antenna
• Instrument Panel Module (IPM)
• Rear Integration Module (RIM)
• Remote Control Door Lock Receiver (RCDLR)
• External RF Antenna (includes coax from RCDLR to back glass)

Remote Control Door Lock Receiver (RCDLR)
The RCDLR is a multi-function module which controls all the vehicles antennas for passive keyless entry functions. The RCDLR also acts as the receiver for active keyless entry and tire pressure monitoring (TPM) functions, as well as controlling all immobilizer functions.
The RCDLR's RF antenna is located in the back glass, and there is a coax cable connecting the glass antenna to the module located in the trunk.

Your best bet , take it to a qualified repair shop that has the factory Tech 2 scan tool or someother professional type scanner that can read • Rear Integration Module (RIM) DTC'S - diagnostic trouble codes .

Two fuse's for the central security module . This module controls the keyless entry .
F1.2 30 amp - location ,battery junction box . ( underhood fuse box) Plus F2.2 10 amp location (CJB) central junction box - inside the vehicle fuse panel .

2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry

Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html

May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...

The keyless entry module or "Driver Door Module" is inside the drivers door and should be clearly marked.

You need to ask the guy you purchased the system from, we have no information on any add on, the factory oneworks through the BCM as far as I know.

HI,
Probably up under the dash - either side.
Gl,
Td

RFA / MOD fuse 10amp . location - insturment panel fuse box. Fuse Block - I/P
Right side of the I/P, behind the access panel
If the fuse is good your best bet would be to take it to a qualified repair shop , that doesn't mean the dealer . Lot of good independant repair shops around , just have to check the yellow pages.
Do you know what DTC'S are ? diagnostic trouble codes ! Not only the ones for the engine management system OBD 2 . There are also DTC'S for the remote keyless entry system , BCM - body control module. You need a factory or professional scan tool to view this codes
DTC B3101
DTC B3102
DTC B3103
DTC B3106

The remote control door lock receiver (RCDLR) communicates with the body control module (BCM) through the keyless entry serial data circuit. When any button on the keyless entry transmitter is pressed, the transmitter sends a signal to the RCDLR. The RCDLR sends a lock, unlock, or panic alarm request to the BCM, depending on which button is pressed on the transmitter. The BCM receives the message and performs the appropriate function. The BCM also uses the keyless entry serial data circuit in order to communicate with the RCDLR when programming transmitters. Do you know what serial data circuits are ?

DTC B3101 Keyless Entry Data Link Circuit Range/Performance
DTC B3102 Keyless Entry Data Link Circuit Low
DTC B3103 Keyless Entry Data Link Circuit High
DTC B3106 Keyless Entry Data Link Parity Error

This is what the factory manual said as to the location of power steering fluid reservoir ! Not much help , you would do better googling it.
The power steering fluid reservoir holds the power steering fluid and may be integral with the power steering pump or remotely located. The following locations are typical locations for the remote reservoir:
• Mounted to the front of the dash panel
• Mounted to the inner fender
• Mounted to a bracket on the engine

Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Disconnect the battery to the car for five mins. Thay should reset the keyless module. I had the same problem

From what I can tell the vsm module is on the inside firewall on left side towards center of vehicle. It will be a black box and should have a white sticker with 4 ro 5 numbers in bold black on it this is your factory code hope this helps