How do I unlock a back seat belt after getting jammed

You must remove the rear seat bottom and remove the bolt for the seat belt retractor, this will allow you to in jam the seat belt.

IN ORDER FOR A SEAT BELT TO UNLOCK U MUST SET IT AT THE RIGHT POSITION OTHERWISE IT WONT UNFOLD!!!REMEMBER DO NOT DROP IT!!

Most Ford products are designed so the seat belt latch by the center console moves with the seat. The bottom of the latch rides on the seat rail, and with time sometimes it builds up a little play on the rail. As the seat moves forward or back, the seat belt guide often tilts forward or back, just a bit, on the rail, and gets stuck. So you can move forward or back just a bit, but then it jams and you can hear the motor, but can go no further.

The long term fix is to remove the seat, disassemble the seat belt guide and rail, and usually replace some parts.

But the short term solution is often to simply hold on to the seat belt latch and rock it forward and away from the seat as you try to go forward or back. Or, sometimes it works best to rock it backwards and away from the seat as you try to move forward or back. It all depends on which way it is binding.

There's no guarantee that it won't jam again if you move it all the way back or forward, but once you find the right position to hold the seat latch in while moving the seat, you should be able to re-adjust it where you need it to be.

Most Ford products are designed so the seat belt latch by the center console moves with the seat. The bottom of the latch rides on the seat rail, and with time sometimes it builds up a little play on the rail. As the seat moves forward or back, the seat belt guide often tilts forward or back, just a bit, on the rail, and gets stuck. So you can move forward or back just a bit, but then it jams and you can hear the motor, but can go no further.

The long term fix is to remove the seat, disassemble the seat belt guide and rail, and usually replace some parts.

But the short term solution is often to simply hold on to the seat belt latch and rock it forward and away from the seat as you try to go forward or back. Or, sometimes it works best to rock it backwards and away from the seat as you try to move forward or back. It all depends on which way it is binding.

There's no guarantee that it won't jam again if you move it all the way back or forward, but once you find the right position to hold the seat latch in while moving the seat, you should be able to re-adjust it where you need it to be.

Most Ford products are designed so the seat belt latch by the center console moves with the seat. The bottom of the latch rides on the seat rail, and with time sometimes it builds up a little play on the rail. As the seat moves forward or back, the seat belt guide often tilts forward or back, just a bit, on the rail, and gets stuck. So you can move forward or back just a bit, but then it jams and you can hear the motor, but can go no further.

The long term fix is to remove the seat, disassemble the seat belt guide and rail, and usually replace some parts.

But the short term solution is often to simply hold on to the seat belt latch and rock it forward and away from the seat as you try to go forward or back. Or, sometimes it works best to rock it backwards and away from the seat as you try to move forward or back. It all depends on which way it is binding.

There's no guarantee that it won't jam again if you move it all the way back or forward, but once you find the right position to hold the seat latch in while moving the seat, you should be able to re-adjust it where you need it to be.

if you try to pull out seatbelts and they are jammed you will have to replace them and as they are part of the airbag safety system ......they aint cheap.....

This happens to me also. To solve the problem you need to un-bolt the seat belt clip. A bit tricky when the bench is tight down, but get a friend to hold it up out of the way as much as possible. This will relieve the tension and allow the seat belt to return to normal. To prevent this in future, pull the seat belt out and clip it in to place before lowering the back bench. This allows enough slack on the seat belt tensioner to stop the problem from happening again.

They have a problem with the seatbelt retractor getting jammed up causing the belt to jam & not let the rear seat fold back up.The easiest way to get the seat back up is to cut the seatbelt & fold up the seat.Then the rear seat needs to be disassembled to gain access to the seatbelt retractor assy which has the seat belt made on.Hopefully it's still under warranty or Ext. warranty.hope this helps

bet the belt is twisted pull back the rubber door seal and remove the top buckle should be possible to remove the trim pull the belt all the way out and untwist   go for it