Question about Hyundai Accent

Open Question

What does it mean when my 2005 Hyundai Accent GS is showing the following Diagnostic trouble codes P0108 - P1505 - P1507 - P0650

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
dsacco86
  • 1077 Answers

SOURCE: what does code 1-p0650 mean?

P0650 Malfunction Indicator Lamp (MIL) Control Circuit Malfunction

Malfunction Indicator Lamp (MIL) is located on the instrument panel. When the ignition switch is turned ON without engine running, MIL will light up. This is a bulb check. When the engine is started, MIL should go off. If MIL remains on, the on board diagnostic system has detected an engine system malfunction.

Possible Causes:

  • Harness or connectors (MIL circuit is open or shorted.)
  • MIL bulb may be faulty
  • Posted on May 10, 2009

    Ad
    ghost45
    • 1280 Answers

    SOURCE: hyundai elantra reading these codes its an 05 car

    ZERO out your ECM (wipe out all 'adaptives'). disconnect both battery post connectors and tough them together for 30 seconds. Afterward, reconnect them to the battery... see what happens

    Posted on Sep 12, 2009

    asetech74
    • 218 Answers

    SOURCE: i got diagnostic trouble codes P0108,P0121,P0340

    Here is what each of your trouble codes means:

    DTC P0108 MAP Sensor Range check High
    DTC P0121 TPS Circuit Range/Performance Problem
    DTC P0340 Camshaft Position Sensor Circuit Malfunction
    Do you know how long each of these codes have been stored? Each one of these codes relate to a different part of the vehicle.

    Your PO108 codes is probably a faulty Manifold Absolute Pressure Sensor
    PO121 is a Throttle Position Sensor malfunction code
    PO340 is a Camshaft Position Sensor malfunction code

    I would not think that all 3 of these codes all set at the same time, just wouldnt make sense unless there was a problem with the Engine Control Module (ECM) causing all these codes to set at the same time.

    Posted on Sep 14, 2011

    • 7 Answers

    SOURCE: diagnostic codes p1505 p1507 ran

    change crank position sensor and blown ecm 15amp fuse

    Posted on Feb 29, 2012

    • 52 Answers

    SOURCE: I own a 2000 Hyundai accent the codes came up with P0717, P0734, P0732,P0108. Please help

    Sorry to tell you that it is incorrect gear ratio codes. Must replace the transmission.

    Posted on Mar 15, 2013

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Error code p0650


    OBD II codes are specific to manufacturers and often specific vehicles. A Hyundai Accent P0650 may not be the same as a Hyundai Sonata P0650 because Hyundai loaded more diagnostic codes into the upscale Sonata.

    Check with AZone or similar, they'll tell you the code description, and give you possible suspect causes to check.

    Jul 24, 2014 | Hyundai Motor 2004 Accent

    1 Answer

    How I fix the code p0650 "?"


    Check engine light is faulty or that the engine computer has run a diagnostic check and one of the systems failed. You can use the diagnostic tool http://www.xcardiag.com/search/?q=+code+p0650
    hope it can help you.

    Apr 28, 2014 | 2005 Hyundai Elantra

    1 Answer

    Ck engine codes


    Possible causes for P1505 & p1507
    Faulty Idle Speed Control Actuator valve, harness is open or shorted, Idle Speed Control Actuator valve circuit poor electrical connection. No the codes are not related to the EGR. P0198 is related to the engine oil temperature sensor. By the way you should use a meter as supposed to a test light. The test light will not be able to measure 5 volts reference or voltage drops. However I would try replacing the affected parts based on the codes and the info you've provided. Good luck.

    Apr 02, 2014 | 2005 Kia Spectra

    1 Answer

    Code p1505 and p1507 interpretation and solution


    Try cleaning the throttly body and air intake. Could also be a bad sensor I would start by cleaning it out real good clear code then drive it

    Oct 23, 2013 | Hyundai Cars & Trucks

    1 Answer

    I own a 2000 Hyundai accent the codes came up with P0717, P0734, P0732,P0108. Please help


    Sorry to tell you that it is incorrect gear ratio codes. Must replace the transmission.

    Mar 14, 2013 | 2001 Hyundai Accent

    2 Answers

    I got diagnostic trouble codes P0108,P0121,P0340 what does it means and give me the remedial action for that


    Here is what each of your trouble codes means:

    DTC P0108 MAP Sensor Range check High
    DTC P0121 TPS Circuit Range/Performance Problem
    DTC P0340 Camshaft Position Sensor Circuit Malfunction
    Do you know how long each of these codes have been stored? Each one of these codes relate to a different part of the vehicle.

    Your PO108 codes is probably a faulty Manifold Absolute Pressure Sensor
    PO121 is a Throttle Position Sensor malfunction code
    PO340 is a Camshaft Position Sensor malfunction code

    I would not think that all 3 of these codes all set at the same time, just wouldnt make sense unless there was a problem with the Engine Control Module (ECM) causing all these codes to set at the same time.

    Sep 14, 2011 | 2003 Hyundai Accent

    3 Answers

    Diagnostic codes p1505 p1507 ran stalled wont run turns over fine


    sorry but their are no diadnostic codes with this number in the manufacturers codes i have
    P0505....Idle Control System
    P0507....Idle Control System RPM Higher Than Expected
    but i have found these generic codes for you if they help

    Aug 10, 2010 | 2003 Hyundai Tiburon

    1 Answer

    Hyundai elantra reading these codes its an 05 car


    ZERO out your ECM (wipe out all 'adaptives'). disconnect both battery post connectors and tough them together for 30 seconds. Afterward, reconnect them to the battery... see what happens

    Sep 11, 2009 | Hyundai Motor 2003 Elantra

    2 Answers

    What does code 1-p0650 mean?


    P0650 Malfunction Indicator Lamp (MIL) Control Circuit Malfunction

    Malfunction Indicator Lamp (MIL) is located on the instrument panel. When the ignition switch is turned ON without engine running, MIL will light up. This is a bulb check. When the engine is started, MIL should go off. If MIL remains on, the on board diagnostic system has detected an engine system malfunction.

    Possible Causes:
  • Harness or connectors (MIL circuit is open or shorted.)
  • MIL bulb may be faulty
  • May 10, 2009 | Hyundai Accent Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    24 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    Marvin
    Marvin

    Level 3 Expert

    85111 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...