Question about 1996 Ford Crown Victoria

Open Question

PO133 Crown Victoria - 1996 Ford Crown Victoria

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

BILL RICHARDSON

  • 508 Answers

SOURCE: 94 CROWN VICTORIA FUEL PUMP

Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Posted on Feb 18, 2009

Ad

Anonymous

  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

Anonymous

  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

Dr Honeydew

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

reisdos

Sean Reisdorf

  • 1297 Answers

SOURCE: fuse diagram for 2000 crown victoria

there are 5+ pages of fuses what specifically do you need


Posted on Jul 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2007 Crown Victoria Police Interceptor vibrate when I get to 40 miles an hour and then die off back to normal by the time it reaches 50


Ford Crown Victoria Questions - what would cause a whole ...

www.cargurus.com > Questions > Ford > Crown Victoria
CarGuruswhat would cause a whole car vibration when going between 48 and 65 mph, even ... Asked by Dfranz Aug 29, 2013 at 11:53 AM about the 2001 Ford Crown Victoria Police Interceptor ... You have an open diff by turning one wheel the driveshaft should turn before the .... 2007 Ford Crown Victoria Police Interceptor For Sale.

Nov 03, 2015 | Cars & Trucks

2 Answers

How to get windows to go up and down in 1995 ford crown victoria


No up
No down
One window
All windows
Window fails down
You hear motor run & no window movement
You work the switches & they work sometimes

I would imagine you need that answered at a
repair shop

Feb 14, 2013 | 1995 Ford Crown Victoria

1 Answer

I need drive belt diagram for a 2002 ford crown victoria


2002 FORD CROWN VICTORIA - V8 4.6L 281ci CNG FI N 9
and
2002 FORD CROWN VICTORIA - V8 4.6L 281ci GAS FI N W

Belt Routing Diagram - Multiple Accessory

f091bd1.jpg


Hope helped (remember rated this).

May 26, 2010 | 2002 Ford Crown Victoria

1 Answer

1997 Crown Victoria: 92 crown victoria get no spark...


Attempt to change all of the spark plug wiring and spark plugs. Then start the vehicle.

May 18, 2010 | 1997 Ford Crown Victoria

1 Answer

Ford crown victoria


you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Mar 06, 2010 | 2001 Ford Crown Victoria

1 Answer

My transmission on my 94 crown victoria seems to


have the fluid changed, the new fluid should cure this.

Nov 02, 2009 | 1994 Ford Crown Victoria

1 Answer

Tail lights not working while drive. brake,blinkers work


i have a crown victoria with brake lights no tail lights could you help me?

Nov 19, 2008 | 1989 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...