Question about 1998 Jaguar XK8

5 Answers

Jaguar XK8 Window Problem

Both passenger & driver windows did not restore to their closed position when doors were opened then closed. Drivers window fixed itself but passenger window won't reurn to "Up" position, it keeps going down when door handle operated.
Any answers would be greatfully received...

Posted by on

  • 4 more comments 
  • stevem260 Mar 20, 2009

    Thanks Bill sounds like maybe the drivers door fixed like that I will try...

  • stevem260 Mar 23, 2009

    Tried that still no joy any more ideas ?

  • stevem260 Mar 31, 2009

    Thanks tchandler worked a treat..

    Regards
    Steve


  • asp1 Apr 13, 2009

    the same as posted both windows do not return to closed position when door closed again XK8 2002 model

  • Kevin Moore Mar 22, 2013

    Many thanks to all, worked a treat.....

  • Mopar Maddy
    Mopar Maddy May 29, 2018

    This is the normal function of the Jaguar XK8 convertibles cars,door windows. Each time you pull up on the outside door handle the window will automatically lower by about a inch. The reason for this design is to clear the door glass from the convertible top once you open your door. Once the doors are shut the door glass automatically goes up about another inch, sealing the door glass behind the convertible tops soft top edge. If it never dropped about a inch you would not be unable to open the cars door. If you ever keep pulling the outside door handle up before shutting the door it will keep lowering the door glass with each pull.
    To reset the windows get in your car and shut both doors. Start car and let it run while in park and foot off gas. Now push the interior door window switch down until the window goes all the way down. Once all the way down it will make a beeping sound. It may take a second or two before it beeps. Stop pushing down once you hear the down beep. Now while still sitting in car with it still in park and running push window switch up until window fully closes and again it will make a beep sound. Once it beeps from up or down quit pushing the interior door window switch. After this is done the windows are now reprogrammed to know full up and full automatic down positions. Do the same now for the passenger side. After fully up beeps and fully down beeps you are done. You may have to redo this from time to time if by mistake you grab the outside door handle too many times. A simple painless fix.

×

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Same thing has happened on mine!
The solution is to reprogram the window limits. You need to sit in the car with doors shut! Turn the key in ignition in position I or II, roll down the window all the way and keep holding the switch for 5 seconds, then roll the window up and again keep the switch pressed for 5 seconds, repeat same steps for other door.
Reprogramming is also described in the owners manual. I don't know how mine became deprogrammed, should only happen if the battery is disconnected!

Posted on Mar 29, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Bill man is right. with doors closed open window and continue to hold switch in position and count to ten, then close window and continue to hold switch in position and count to ten. Do both windows this way. I had the same problem when my battery went dead.

Posted on Mar 29, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

It is just a problem of having lost the position memory of the windows.
Does not need any repair but a resetting process of the Electronic Central Unit that controls the setting of windows motors.
That is why in any maintenance operation that will require to disconnect the battery you will have to leave the doors opened


Reg

Posted on Mar 27, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Try operating window to bottom position and hold switch down for a few seconds.
This cured it on my one

Posted on Mar 19, 2009

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Thanks to all, worked a treat.

Posted on Mar 22, 2013

  • christopher wheeler
    christopher wheeler Dec 25, 2013

    Worked for me on my 2005 XKR conv,thank you so much

×

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 pontiac g6 drivers window, when handle is lifted the window does not drop the inch or so that it should.


The window indexing feature is used to lower the driver and passenger power windows approximately 4 mm when the door is opened. This is necessary to allow the top edge of the window to clear the window weather-strip. This feature will also raise the window to the fully seated position once the door is closed.
Is just the driver door not working ?
Observe the operation of the driver window and front passenger window while opening and closing their respective doors. The windows should index DOWN and UP when the doors are opened and closed.
? If either window does not index UP or DOWN, refer to Window Index Feature Malfunction.

Window Index Feature Malfunction
Ignition ON, observe the scan tool Driver Door Ajar Sw and Door Ajar Switch parameters while opening and closing the driver and passenger doors, the parameter should change from Door Closed to Door Ajar.
? If the parameter does not change when opening and closing the doors, refer to Door Ajar Indicator Malfunction .
Ignition OFF, disconnect the harness connector at the appropriate window motor.
Ignition ON, with the door closed, test for greater than 10 volts between the signal circuit terminal 5 and ground.
? If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
With the door open, test for less than 1 volt between the signal circuit terminal 5 and ground.
? If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
If all circuits test normal, replace the window motor.

Your best bet mite be to take your vehicle to a qualified repair shop (GM dealer )

Nov 13, 2017 | Pontiac Cars & Trucks

1 Answer

Why does the power window button blink on and off and the automatic feature doesn't work in the 2008 Toyota Sienna?


NOTE:
Anytime the batteryterminal has been disconnected, please initialize the driver's door power windowand front passenger's door power windowafter reconnecting the batteryterminal.

With ignition switchin the "ON" position, do the following:

1. Push down and hold the driver's door power windowswitch to completely open the window.
2. Pull and hold up the driver's door power windowswitch until the window closes.

Continue holding the switch for approximately one second until the switch changes from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power window switchfor the passenger's door windowshould be blinking.
4. Push down and hold the passenger's door power windowswitch to completely open the window.
5. Pull and hold up the passenger's door power windowswitch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

Feb 09, 2016 | Toyota Cars & Trucks

1 Answer

Fix for the door glass,2009 CHALLENGER. Won't reset to down position when opening door to allow window to break seal.Then move up and seal glass when door is closed. SMart Glass?


This may be as simple as relearning the window stop positions. Perform the following procedure to relearn the windows;

1) Sit in the drivers seat and ensure both doors are fully closed.
2) Turn the key to the ON position but do not start the vehicle.
3) Pull up on the drivers window switch until the window reaches the full up position, then CONTINUE HOLDING THE SWITCH UP for 2-5 seconds, then release the switch.
4) Push down on the drivers window switch until the window fully opens, then CONTINUE HOLDING THE SWITCH DOWN for 2-5 seconds, then release the switch.
5) Repeat steps 1-4 for the passenger window.
6) Close both windows and check the operation of the smart glass.

Let me know if you need further help.

Nate

I’m happy to assist further over the phone at https://www.6ya.com/expert/nathan_cc888cf971f43e78

Oct 18, 2014 | 2009 Dodge Challenger

1 Answer

The central locking on my 1999 Jaguar XK8 has stopped working. The fob does not work to lock/unlock the doors but does unlock the boot and turn on the lights. The drivers door can only be locked/unlocked...


sounds like one of the switches has failed on the drivers door latch that means a new latch unit is needed or it may be the drivers door module has failed more than likely the latch

Jul 22, 2017 | Jaguar X-Type Cars & Trucks

1 Answer

I have a 2004 XK and when I open the door, the window goes down a little (as it is supposed to) and then rises back up to the closed position. This causes the door to refuse to close. To close the door, I...


1. roll drivers window all the way down and hold it till it clicks.now roll it up all the way and hold it till it clicks.
2. do same with passenger window.
now your windows should work properly.
good luck.

Jul 02, 2017 | Jaguar XK Cars & Trucks

1 Answer

2006 Audi A6 Avant Drivers window control panel


Replace the switch. It has lost connection to the up position.

Sep 11, 2010 | 2006 Audi A6

1 Answer

Door latch fails intermittently (1997 Jaguar XK8)


it should be the door selenoid causing the problem it has the linkage attached to it and would give you the problems you discribe

Jul 10, 2010 | 1997 Jaguar XK8

1 Answer

Passenger window operates intermittingly. When it


The problem could be in the master window switch on the drivers door, or the window motor could be going out, but most likely the cause is a broken wire inside of the weather boot that runs between the door and the body of the vehicle, and the broken wire is making intermittent contact because the door is being opened and closed all the time, and sometimes the wire will touch and make the connection and that is why it only works sometimes.

Try this the next time that the window stops working, hold the window switch down in whatever direction that you want the window to go (up or down) and while holding the switch in that position open and close the drivers side door and move or wiggle around the weather boot that contains the wiring that is between the door and the body of the vehicle, and do the same for the passenger side door, if the window starts working while you are holding down the window switch and opening and closing the door or moving around the weather boot between the door and the body of the vehicle, then there is a broken wire or even wires that will need to be repaired.

The broken wire can be on either the passenger side, or most likely on the drivers side, and if you do find a broken wire or wires, then you should repair the wires by soldering them well and use the same gage wire if you need to lengthen the wire to repair it successfully, and do not use a wire connector if you want the repair to last.

Jun 02, 2010 | 1996 Plymouth Voyager

Not finding what you are looking for?
1998 Jaguar XK8 Logo

7,875 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...