Question about 1998 GMC Sierra
On a 1998 GMC sierra, I Have replaced the heads, timing chain, done a tune up, also I replaced the crank sensor, on the advice of someone else and STILL it shows this code. Ran a test of the cam sensor got 11.3 volts but according to the picture in the haynes manual I got it on the sensor ground wire not the 12 volt supply wire. Is the picture in the manual inncorrect or maybe the PCM. Just to be sure i checked that the timing mark is lined up and the distributor is pointing to #1. Truck also runs well at idle but has a violent stall at higher rpms. I understand that I need to perform a crank relearn procedure also. Will this fix the issue. Thanks for any inputs!
I had this same P1345 code on my 1998 GMC K1500 5.7 for about 2 years. Each time the code was erased, the "Service Engine Light" came right back on with the same code. I tried replacing the cam sensor, but that didn't solve it. I had the timing adjusted, it was out -13 degrees. After adjustment, the "Service Engine Light" went off, but only for a short time. Adjusting the timing is just a temporary mask on fixing the real problem and eventually you will run out of adjustment. I read about this same problem on another forum and someone recommended changing the distributor gear. So I checked the gear and a the teeth were worn. Replaced the gear ($35 part), readjusted the timing and the light has been off ever since. Apparently the gears in 96-99 are soft and wear enough to throw off the timing. This code is telling you the crank and distributor are out of sync. So before you start buying sensors and other misc. parts, try the distributor gear if you are getting a P1345 code.
Posted on Mar 26, 2009
When you remove the camnshaft, or move the distributor on 1996 and newer gmc pickups you change the cam timing, to correct this you must use a scan tool that can access the data readings from the cpu, it will tell you the cam timing, you can only be + or - 2 degrees. using the tool while the engine is running you move the distributor slightly, clockwise is advance, counterclock wise retards, after moving the distributor rev the engine to 2500rpms and it will recalculate the timing on the cam, once you get it zeroed out tighten the distributor hold down bolt and clear your troble codes. There are no timing marks on your engine to use an inductive timing light.
Posted on Apr 24, 2009
I have a k2500 pick up 5.7 engine I had the intake go bad and leak coolant into the engine. Replaced intake gaskets and now runs ruff at idle and also has code1345 cam crank corolation will this effect Idle seems to have power ect.
Posted on Aug 31, 2011
RELEARN MAY JUST BE CLEARING THE MENORY OF THE POWERTRANI CONTROL MODULE, BUT THE CODE INDICATES THAT THE CAM SIGNAL IS NOT MATCHING WHERE THE CRANKSHAFT SAYS IT SHOULD BE, DID U USE THE FACTORY CAM GEAR WITH THE MAGNET EMBEDDED IN IT ? IF NOT THEN THERE IS NO WAY TO TRIGGER THE SENSOR, CHECK THAT.
Posted on Mar 03, 2009
1996 chevy 5.7 idles high.get a 1345 code with scanner
Posted on Mar 19, 2010
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Jul 19, 2015 | GMC Cars & Trucks
Jan 22, 2013 | 1996 Chevrolet Tahoe
May 24, 2017 | 1999 GMC Suburban
Jul 18, 2012 | 1999 GMC Suburban
Jun 08, 2011 | 1998 Chevrolet K1500
May 27, 2010 | 2002 GMC Sierra
Mar 12, 2010 | 2001 Toyota Sienna
Nov 18, 2009 | 1998 GMC Sierra
Nov 08, 2009 | 1998 GMC Sierra
Sep 18, 2017 | 1998 GMC Sierra
9,889 people viewed this question
Usually answered in minutes!