How do i replace a turbo in a 2008 Sierra GMC

Gary Queen

• 85 Answers
• Posted on Nov 12, 2008

SOURCE: How to replace side mirror on 1996 GMC Sierra?

See Figure 2
Fig. 2: Outside mirror-below eyeline type

1. Remove the mirror cover screw and lift the cover and pivot the mirror towards the window.
2. Remove the mirror to door bolts and remove the mirror and seal from the door.
3. To install, position the mirror and seal to the door and install the retaining bolts.
4. Pivot the mirror away from the window, and lower the mirror cover.
5. Installation is the reverse of removal.

SOURCE: gmc sierra 2008 low tire pressure problem

You can follow this to reset it.
Ignition ON, initiate the TPM Learn Mode
using one of the following procedures:

1. On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
   
2. On vehicles not equipped with keyless entry, press and release the driver information center (DIC) INFO button until the TIRE LEARN message appears on the DIC display. Press and hold the SET/RESET button until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
3. Increase/decrease the tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate.
   After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 2 for the remaining 3 sensors in the following order:
   3.1. Right front
   
   3.2. Right rear
   
   3.3. Left rear
   
   When the left rear sensor has been learned and a double horn chirp has sounded, the learn process is complete and the RCDLR exits the learn mode.
   Ignition OFF, adjust all tires to the recommended pressures

SOURCE: 1997 GMC Sierra Ignition Switch Replacement

take off the cover on the top and bottom of the steering column just behind the wheel. pop the tilt lever out simply just by grabbing it and give it a good tug. then once you have the new switch and you get in there your going to need an inverted torx socket to remove the small bolts that hold the switch to the column. do not move the gear on the new switch make sure it lines up exactly as the old one did!!!!!!!!!!!!

SOURCE: replace sway bar end links '97 GMC Sierra

if you put your vehicle information in at advanceautoparts.comyou can search sway bar and find parts that you need - there was someinfo missing on which sierra model you have as far as engine size andvin # match but I came to: http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Sway-Bar-Link-Kit_78_R|GRPCHASAMS__sway%20bar___

SOURCE: Do you have instructions on removing and replacing

REMOVING
Removing the master cylinder is really simple, only requiring a few steps. Keep in mind that brake fluid will eat the paint of the car. So use a plastic or vinyl type fender cover to protect the vehicle's paint. Brake fluid is water soluble so if you should get some on the paint, wash it off with plenty of water as quickly as possible.

1. Using a siphon, an old turkey baster works great, empty the master cylinder reservoir and dispose of the old brake fluid in the proper manner.
2. Disconnect the wire connector for the brake fluid level and/or brake pressure-warning switch, if your vehicle is so equipped.
3. Disconnect the brake lines from the master cylinder with a line wrench. A line wrench is specially designed to remove and install hydraluic fittings without rounding them off.
4. Remove the master cylinder mounting nuts, then the master cylinder.
5. On non-power brake vehicles, disconnect the master cylinder linkage from the brake pedal underneath the dash.
6. On models with separate fluid reservoirs, remove the reservoir.

1. Begin by removing the cap.
2. Follow the directions that come with the kit to select the suitable adapters, and then connect the adapters and tubes to the ports on the cylinder. The other ends of the tube extend down into the master cylinder, and are held in place by a plastic clip. Figure 2.
3. With the bleeder kit installed, fill the master cylinder about halfway with new brake fluid. Use a large screwdriver to depress the valve assembly inside the master cylinder. If you do not have a vise you can mount the master cylinder on the vacuum brake booster and bleed the master cylinder.
4. Small bubbles will appear in the fluid. Continue working the valve assembly until no more bubbles appear. This indicates that the cylinder has been thoroughly bled.Reverse the removal procedure to install the master cylinder, noting the following Refer to your service manual for any Master Cylinder Push Rod Adjustment procedures if your vehicle requires it.Bleed brakes as described under Brake Bleeding.Operate the brakes several times and check for external hydraulic leaks.This is fairly straightforward job. Replacing a master cylinder should take you about 1 to 2 hours, depending on the make and model of car. If you are rebuilding the master cylinder, add about another hour or so.