95 maxima starts ok but when you accelarate it won't go over 2000

HELP!! No Heat Only cold Air - Maxima Forums

maxima.org/...maxima-1995.../575092-help-no-heat-only-cold-air.html

Oct 30, 2008 - Ok this is the deal i have 95 gle auto climate control. its soo dam cold here in ... its was low filled it still no heat when i was messing with the climate control i was setting .... 1999 Auto Nissan Maxima SE-Limited Crimzon Blaze Bad Engine Coolant Temp Sensor=No heat?
Dec 11, 2010
coolant change - no heat
Nov 28, 2010
No in cabin heat & engine overheating
Dec 6, 2009
whats the cause of getting no heat?
Feb 14, 2003
More results from maxima.org

No heat,

If the transaxle is all factory original & it does not
up shift as well as has a code & no OD,then you
may as well put it out & rebuild it.

Close to 14 years is great for any transmission.

In the future you change your trans & power steering
fluids every 3 years & at first sign of any trans issue
you stop driving it immediately,drive no more than
5 miles to get home or to a shop or you have what you
have , a $3,000.00 bill coming up to pay

ckeck the tps and maf sensors

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Hi there:



Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

could be as simplet as blown fuse for radio. i would start there. look at your "audio" fuse in the fuse box. if thats ok, then you have something elses goin on, but start with fuse check.

have your starter checked? if ok, check ignition switch and fuses!!

Could be battery, starter or coolant sensor.

It is hard to understand / get across engine noises with words so difficult to diagnose over the net but try to push start the car and let me know if it starts ok with a push. Also, maybe try a jump start, preferably using a circuit protector if you have one.
Let me know results of the above.

Lloyd

I had a 94 which i fixed this same type of problem by putting in a new distributor

Remove the high tension cable to the distributor from the ignition unit. Conduct a spark test. If there's no spark, try to replace the ignition coil or the igniter.