20 Most Recent 2001 Nissan Maxima Questions & Answers


if its brakes it will be on your brake calliper if its coolant it should be next to your thermostat

2001 Nissan... | Answered on Jun 11, 2019


I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

2001 Nissan... | Answered on Feb 25, 2019


Replace both, if one is bad chances are that the other will go zoon anyway. By the way the engine code should tell you which side is bad.

2001 Nissan... | Answered on Jan 01, 2019


Internal radio problem. There are two plugs for the CD in the radio. One for input/power. The other is for output/sound. If it is an expensive radio, pull the case off, look at the CD player and find the plugs to the main board. Unplug them and plug them back in, hook up the radio and see if it works.(could be that simple) Then reassemble the case. If it factory or cheap, just replace it with an aftermarket radio. This would be cheaper than an electronic repair.

2001 Nissan... | Answered on May 02, 2018


You have a bad head gasket. The antifreeze is blowing out your exhaust. Do this before you do more damage. Good Luck Friend.

2001 Nissan... | Answered on Feb 20, 2018


ck for a fuse in the under the hood fuse box that says bsm may be blown.
Also try this.....
To reset the security system remove the negative battery cable for 30 minutes, then reconnect the cable. Next, lock and unlock the doors using the remote. This will reset the alarm system and the engine will start and fobs reset.

Here are some factory notes....FYI

Anti-Theft Systems

PROGRAMMING

NOTE: If a new Smart Entrance Control Module (SECU) is installed, a new identity code must be entered and all remote controllers must be programmed. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.

PROGRAMMING > PROGRAMING NEW ID CODE

NOTE: This procedure will erase all previous identity codes and render all previously programmed remote controllers inoperative (until reprogrammed). All remote controllers to be used with system must be programmed at the same time. A maximum of 4 remote controllers can be programmed. Any attempt to program more than 4 controllers will be ignored. If same identity code is entered more than once, entry is ignored even though hazard warning lights will still flash twice.
1. Close and lock all doors. Erase original identity code(s) by inserting and completely removing key from ignition switch more than 6 times within 10 seconds. Hazard warning lights should flash twice. Turn ignition switch to ACC position.
2. Push any button on new remote controller once. Hazard warning lights should flash twice, indicating identity code has been entered. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
3. For each additional remote controller to be programmed, manually release door lock and lock again by using door panel switch and repeat step 2. If no additional remote controllers are to be used, exit programming mode by unlocking and opening driver's door.

Please let me know if you need anything else to get the problem fixed. Happy mew Year!

2001 Nissan... | Answered on Jan 03, 2018


You just go to the link I attached I'm sure you will get the solution of your problem 2001 Nissan Maxima

2001 Nissan... | Answered on Nov 29, 2017


code p 0138 refers to 2 items
1--heated oxygen sensor(HO2S) 2 bank 1--high voltage ==causes --wiring short to positive --HO2S---ECM
2--oxygen sensor (O2S) 2 bank 1--high voltage ===causes wiring short to positive ---ECM
code p 0139 refers to 2 items
1--- heated oxygen sensor (HO2S) 2 bank 1--slow response ===causes --heating inoperative --wiring--ECM
2--oxygen sensor (o2S) 2 bank 1 slow response ===causes --wiring --- O2S

heated oxygen sensors9HO2S) are in the exhaust manifold before the cat converter
Oxygen sensors (O2S) are after the cat converter
it is indicated that the HO2S is faulty-
check the wiring and /or replace both sensors

2001 Nissan... | Answered on Nov 16, 2017


Fuel pump is not pumping hard enough anymore. Have a mechanic check the pressure. Either pump is bad or the fuels filter is clogged. One other thing that causes this is a clogged Calalytic Converter.

2001 Nissan... | Answered on Oct 27, 2017


There is a large battery cable that feeds the solenoid, usually the uppermost connection if the older type. The smaller cable feeds the smaller connector and is the starter power switch.

2001 Nissan... | Answered on Oct 23, 2017


No, a P0449 could never cause a "no crank" condition.

2001 Nissan... | Answered on Sep 26, 2017


You have a bad ground by the lamp fixture. You grounded the circuit and completed it with the wire to car body.

Check all over the lamps for corrosion

2001 Nissan... | Answered on Sep 22, 2017


Check for vacuum hose disconnected--especially under the car by the muffler.
Do It Yourself Diagnosis and Repair

2001 Nissan... | Answered on Sep 04, 2017

Not finding what you are looking for?
2001 Nissan Maxima Logo

794 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2000 Nissan Maxima
2000 Nissan Maxima

1,262 Questions

1995 Nissan Maxima
1995 Nissan Maxima

1,089 Questions

1996 Nissan Maxima
1996 Nissan Maxima

984 Questions

1997 Nissan Maxima
1997 Nissan Maxima

839 Questions

2004 Nissan Maxima
2004 Nissan Maxima

751 Questions

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maxima Nissan

  • Maxima Nissan

Most Popular Question

will code p0449 cause engine not crank

  • Cars & Trucks
Loading...