Cars & Trucks Logo

Related Topics:

Steven Quinones Posted on Feb 27, 2012

How to remove sunvisor clip on a 1997 Honda civic dx?

97 honda civic dx sunvisor clip

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Jul 11, 2012
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Jul 11, 2012
Answers
1
Questions
0
Helped
825
Points
1

I have a 96 Honda Civic and my clip broke. Finally got a new one and could figure it out. Finally did. Rotate the visor out of the way. Rotate the clip 90 degrees CCW. Gently pry down on the clip and remove. Installation of the new clip is opposite the removal.
how to remove sunvisor clip on a 1997 Honda civic  - 7_11_2012_5_40_00_pm.jpg

  • Lloyd Grayson
    Lloyd Grayson May 07, 2014

    removal the same way..it's the cover over the actual sunshade removal.

×

5 Related Answers

Jimmy James

  • 260 Answers
  • Posted on Aug 18, 2009

SOURCE: my 97 honda civic dx check engine light keeps coming on

Had this issue did you replace the exhaust

Ad

Anonymous

  • 15935 Answers
  • Posted on Apr 05, 2009

SOURCE: How to change upper control arm on 1996 Honda Civic DX ?

UPPER CONTROL ARM:

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.

  1. Raise and support the vehicle safely.
  2. Remove the front wheels. Support the lower control arm assembly with a floor jack.
  3. Separate the upper ball joint from the steering knuckle using a ball joint separator tool.
  4. Remove the self-locking nuts from the upper arm anchor bolts. Remove the upper arm from the vehicle.

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
To install:
Use new self-locking nuts when installing the upper arm and strut.
  1. Install the upper control arm assembly into the strut tower.
  2. Connect the upper ball joint.
  3. Install the front wheels and lower the vehicle.
  4. With all four of the vehicle's wheels on the ground, torque the upper control arm nuts to 47 ft. lbs. (65 Nm). Torque the castle nut to 32 ft. lbs. (44 Nm); then, only tighten it enough to install a new cotter pin.
  5. Tighten the wheel nuts to 80 ft. lbs. (110 Nm).
  6. Check and adjust the vehicle's front end alignment.
The bushings on the front lower control arms are replaceable on most models.
This procedure requires the use of a press and may be above the skill range of the average driveway enthusiast. It is recommended that this procedure be done by a qualified machine shop if you are not skilled in the proper use of a press.
  1. Remove the lower control arm that is in need of new bushings.
It is recommended that both the left and right lower control arm bushings be replaced at the same time. The vehicles handling may become unstable if there are new bushings on one side of the car and worn ones on the other.
  1. Set up the control arm in a press.
  2. Using a impact socket of the correct length and size, press out the old bushing.
  3. Install the new bushing by slowly using the press to push it into the control arm.
  4. WARNINGExcessive force could cause the bushing to bend or tear so be careful.
  5. Once the bushing is properly seated in the control arm, remove the arm from the press and install it on the vehicle.

Anonymous

  • 173 Answers
  • Posted on Jul 29, 2009

SOURCE: oil filter in civic 97

If you go to a reputable motor factor,
you can only be sold the correct filter for the civic.
As there are soo many variables in engine type, it's almost impossible to tell, oil volume, or which type filter.
However, I will say, be sure that you don't mix semi-synthetic oil, and mineral oil.
Oil changes should be undertaken every 30,000 miles, (unless under extra work load, (in which case, slightly more regularly))

Otherwise, 10/40 or 15/40 grade oil, is perfectly fine.
The trick to not overfilling the oil, is simply just to take your time, clean the dip stick and retry, until you have the correct reading.

Please don't forget to rate:)

Anonymous

  • 713 Answers
  • Posted on Aug 27, 2009

SOURCE: 1996 honda civic dx interior dash lights turn, headlights on.

it is more than likely a short in the headlight switch. also try the dimmer switch on the dash for the dash lights.

Anonymous

  • 11896 Answers
  • Posted on Sep 11, 2009

SOURCE: how to remove transmission on 97 honda civic dx

remove crossmember, axles, cables, tranny mount bolts (3), tranny to engine of course bolts

Go to autozone.com and register for full free online repair manual

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

DX. Why are rear wiper and hazard signals not working?

Honda Civic How To: Hazard Switch Bulb - YouTube

? 4:54
www.youtube.com/watch?v=P3TqheRsX1w
Sep 25, 2013 - Uploaded by Honda Civic How To
Hi in this first video i will look at how you can easily change a failed bulb in a 2001-2005 Honda civic's hazard ...

DIY] 92-00 Civic REAR Hatch Glass Intermittent Wiper ...

honda-tech.com/honda-civic.../%5Bdiy%5D-92-00-civic-rear-hatch-glas...
[DIY] 92-00 Civic REAR Hatch Glass Intermittent Wiper Retrofit Guide ... The answer lies in a 1997 Honda CR-V. So the 98+ CR-V models all had their rear ... Remove the Rear Intermittent Washer/Wiper Relay from the under-side of the dash, ...
0helpful
1answer

Trying to find fusable link in 97 honda civic dx. Starter and the solenoid are good, but still no power, no turn over, just plain dead everywhere.

There are none. It uses maxi fuses, not fusible links. Here are the two fuses to check that supply power to the ignition switch: fuse 41, an 80 amp battery fuse, and fuse 42, a 40 amp IG1 fuse (ignition 1).
1helpful
1answer

The speedometer quit working in my 97 dx civic

Hi:
You most likely only have two possible parts to consider: the speed sensor, and the actual speedometer in the dash. It is hard to narrow it down without much more info, but that is pretty much the entire system.
4helpful
2answers

How to remove transmission on 97 honda civic dx

remove crossmember, axles, cables, tranny mount bolts (3), tranny to engine of course bolts

Go to autozone.com and register for full free online repair manual
0helpful
2answers

My 97 honda civic dx check engine light keeps coming on

Had this issue did you replace the exhaust
0helpful
1answer

Knockes when clutch petal is released but goes away when pushed in

Does it drive fine. Does it do it in all gears? Or does it go away in 4th?
0helpful
1answer

Need to remove window crank on 1996 honda civic

I have a 97 honda accord and it is helpful to have the tool to remove the clip. you can pick one up pretty reasonably at the local car store. it's pretty much a flat tool that fits between the handle and the door pane.'
Not finding what you are looking for?

835 views

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...