Timingbeltinstallation need information on installing timing belt and set timing

First thing you need to tell us is the manufacturer, year, model, and engine size of the vehicle. Many vehicles have interference engines. These engines, if the timing belt breaks, will invariably suffer internal damage to the valves and possibly the pistons. Simply replacing the belt(s) will not fix these engines. And even where there is no damage, such as replacing a worn, but not broken belt, care must be taken when replacing timing belts on interference engines since excessive movement of the camshaft or crankshaft without knowing where it is physically located can cause damage. On an interference engine, once the belt breaks, you are best to remove the head(s), inspect for damage and repair as necessary. Then, prior to re-installation of the heads, position the crankshaft and camshafts properly and secure them in place when installing the head(s). Then install the belt. If the vehicle does NOT have an interference engine, then you have a much easier go of things as there is no chance of internal damage due to the belt breakage. We simply need the vehicle info to inform you on how to find the marks and set the alignment.

Let's make this easier if you go to your auto parts store and pick up a timing component kit you will have all the parts to do the job .it comes with information on how to replace timing belt and how to set it up I only install kits in my shop so I know that the job is done properly the frist time.

Hi there:

Check this information...

Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks

1. Align marks on camshaft pulleys with alignment marks on seal plate.
2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
3. Loosen tensioner lock bolt.
4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)

1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
2. Timing Belt Installation
   

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Hi there:Check this information...

Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks

1. Align marks on camshaft pulleys with alignment marks on seal plate.
2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
3. Loosen tensioner lock bolt.
4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)

1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
2. Timing Belt Installation
   

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)

1. Pusher

• Tighten bolt to the specified torque.

Torque 19 N-m (19 lb-ft)

1. Timing belt cover

• Remove crankshaft pulley that was installed in step 9.
• Tighten bolts to the specified torque.

Torque 17 N-m (12 lb-ft)

1. Oil cooler hose

• Tighten oil cooler hose bracket bolts to the specified torque.

Torque 22 N-m (16 lb-ft)

1. Crankshaft pulley assembly

• Using special tool J-8614-01, hold the crankshaft pulley.
• Tighten center bolt to the specified torque.

Torque 167 N-m (123 lb-ft)

1. Crankshaft pulley; P/S belt

• Tighten fixing bolt to the specified torque.

Install the belt on the idler pulley.

Timing Belt "Marks"?
CLICK on the following LINK. It has the Timing Belt Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1997/make/toyota/model/camry/1997_toyota_camry_timing_belt_diagram_marks.htm

With your Email Address I will send ALL INFO [email protected] < ME

Caution: Incorrect removal or installation of the timing belt can result in damage to internal engine components.

For complete Timing Belt Removal and Installation information

THIS IS YOUR TIMING BELT DIAGRAM .CAMSHAFT AND CRANK PICTURE .

Kiatechinfo.com will get you all the information you need when working on a kia 2nd only to a chiltons or haynes manual.

For kiatechinfo.com register (its free) then select the information for your car make model engine. Then either do a search for timing belt or pick from proper items in cloumn to the left.

i need timing belt diaghram with more information on balance shaft and belt instaling procedure,as I recenlty fitted the balance shaft belt wrong!