What is the window regulator - 2005 Jeep Liberty

cable? (electric>?)
here is the page on motor;reg.

1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
   • Remove door trim panel.
   • Remove isolator.
   • Remove front door glass.
   • Loosen bolts attaching regulator to inner door panel.
   • Remove bolt attaching regulator to inner door panel.
   • • Lift regulator upward to disengage bolts from door inner panel.
     • Disengage power window regulator harness connector, if equipped.
     • Remove regulator through access hole in door
   • Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
   • Remove the power window motor from the window regulator.

IF YOU REPLACING WINDOW GLASS OR SEAL LOWER THE WINDOW DOWN ENOUGH TO ACCESS GLASS CHANNEL BOLTS TO REMOVE THE WINDOW GLASS.IF WINDOW REGULATOR IS FAULTY YOU CANT REMOVE PARTS ON WINDOW REGULATORS AND REPLACE THEM. YOU HAVE TO REPLACE WINDOW REGULATOR.WINDOW REGULATOR IS UNDER SPRING TENSION IF YOU TRY REMOVE PARTS FROM WINDOW REGULATOR YOU CAN GET HURT.

usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal

1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
   
1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
3. Disconnect window regulator electric drive harness connector.
4. CAUTION: Be careful not to strike or scratch front door window glass because it can break.
   Remove window regulator electric drive retaining screws through holes.
5. Remove window regulator electric drive (23394) from front door power window regulator.
6. Raise front door window glass to full up position by hand and secure with tape.
7. Go to Step 5.
   
   
2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
3. Remove front door window glass as described.
   
4. Disconnect window regulator electric drive harness connector.
   
5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.
   
   Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
   
6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
   
7. Remove two window regulator retaining nuts.
   
8. Remove front door power window regulator from front door (20124).
   

Installation

1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
   

1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
   

1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
   

1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
   

1. Install two upper front door power window regulator retaining nuts.
   

1. Install window regulator electric drive with three screws. Do not overtighten screws.
   

1. Connect the window regulator electric drive harness connector.
   

1. Install front door window glass.
   

1. Adjust front door window glass as described.
   

1. Install front door trim shield and front door trim panel. Refer to Section 01-05
   

Motor Replacement - Power Window

Removal Procedure
Be very careful
Hope this helps




Caution: Do not attempt to service the regulator motor withoutreleasing the counterbalance spring tension. The regulator lift arm isunder tension from the counterbalance spring and can cause personalinjury if the motor is removed from the regulator.

1. Remove the window regulator.

1. Drill a hole through the window regulator and the sector gear.

1. Install a bolt and a nut through the hole in order to lock the sector gear in position.
2. Drill out the rivets that secure the power window motor to the window regulator.
3. Remove the power window motor from the window regulator.

Installation Procedure

1. Install the power window motor to the window regulator.

Important: Remove the nut and the bolt that were used in order to secure the sector gear in position.

1. Install the rivets in order to secure the power window motor to the window regulator.
2. Install the window regulator.

Glass & Regulator

Fig. View of inner door frame and window regulator assembly

1. Lower the window glass and remove the door panel.
2. Carefully peel off the door screen so that it can be reused.
3. Raise the window enough to reach the regulator bolts, hold the glass underneath and unbolt the glass from the regulator.
4. To remove the glass, raise the glass by hand and tilt it as necessary to remove it from the track.
5. To remove the regulator, lower the glass carefully to the bottom of the door and remove the bolts to remove the regulator.
6. Installation is the reverse of removal. Tighten all bolts to 61 inch. lbs. (7 Nm).

Fig. Installing the door glass regulator

Motor

1. Remove the door panel.
2. Carefully peel off the door screen so that it can be reused.
3. Unbolt the window from the regulator and carefully lower it to the bottom of the door.
4. Disconnect the wiring and remove the motor mounting bolts.
5. Remove the 3 guide rail bolts and lower the motor and guide rail assembly out the bottom of the door.
6. Installation is the reverse of removal.

NOTE The upper cable must be below the guide rail mounting bracket.
Showing window regulator motor, or assembly carrier with window regulator, removal/installation

Fig.

NOTE The illustration shows the removal and installation of the window regulator motor/assembly carrier with the window regulator on the rear doors. The procedure for removing and installing on the front doors is the same.

Fig. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier. Remove the screws and take off the window regulator motor

1. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier.
2. Remove the screws and take off the window regulator motor.

To install:

1. The gearing will move when the window regulator motor is removed; it is then no longer centered. The gearing must be aligned when the window regulator motor is installed until the window regulator motor is centered again.
2. Installation is the reverse of the removal (see illustration).

Motor & Regulator

NOTE The illustrations in the procedure show the replacement of the window regulator motor/carrier assembly with window regulator for rear doors. The procedure for front doors is the same.

1. Remove the front or rear carrier assembly.
2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
3. Unfasten the bolts (1) and remove window regulator.
   
   
   

   Fig. Unfasten the bolts (1) and remove window regulator
   

To install:

NOTE By removing window regulator motor, gearing shifts, it is not centered.

Fig. By removing window regulator motor, gearing shifts, it is not centered

1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
3. Carrier assembly with window regulator, installing:
   1. For replacement part carrier assemblies, the gearing is secured in place with a cable tie.
      
      
      

      Fig. For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)
      

   2. Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.
4. Remove the cable tie .
5. By removing window regulator motor, gearing shifts, it is not centered.
6. When installing window regulator motor, gears must be aligned until window regulator motor is centered again.
7. Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.

Hope this helps to solve it.

Please don't forget to rate! Thanks!!!

Motor & Regulator

1. Remove the front or rear carrier assembly.
   
2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
   
3. Unfasten the bolts (1) and remove window regulator.
   

Unfasten the bolts (1) and remove window regulator

To install:

NOTE:By removing window regulator motor, gearing shifts, it is not centered

1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
   
2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
   
3. Carrier assembly with window regulator, installing:
   
   • For replacement part carrier assemblies, the gearing is secured in place with a cable tie.
     

For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)

Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.

Remove the cable tie .

By removing window regulator motor, gearing shifts, it is not centered.

When installing window regulator motor, gears must be aligned until window regulator motor is centered again.

Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 23; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Window Regulators and Motors - REMOVAL & INSTALLATION

NOTE Some window regulators are retained at least in part, by heavy-duty pull rivets. To remove these rivets, the center mandrel must be pushed through with a small punch, and the rivet(s) drilled out with a 3 / 16 inch drill bit. The factory recommended repair requires the use of the same quality of heavy-duty pull rivet.
Front
CHEVROLET



Fig. Typical W-Body power window regulator and bolt tightening sequence



Fig. Chevrolet models use a cross-arm type window regulator
Coupe and sedan front doors use a cross arm regulator. The following procedures are required for removal and replacement of both power and manual window regulators.

1. Remove the door trim panel, as outlined in this section.
2. Remove the plastic sheet water deflector and the energy absorber (foam pad).
3. Remove the door window. Please see Door Window Glass, Removal and Installation in this section.
4. Detach the electrical connector, if equipped.
5. Remove the window regulator bolts and the regulator cam nut.
6. Drill out and remove the pull rivets.
7. Remove the window regulator cam bolt.
8. Remove the window regulator from the vehicle.

CAUTION Do not attempt to service the window regulator motor separately. It is part of the window regulator. The regulator lift arm is under tension from the counterbalance spring and can cause personal injury if the motor is removed from the regulator. The door window regulator cannot be serviced separately. If defective, replace the regulator and motor as an assembly.
To install:

1. Position the regulator by inserting the bottom through the access opening in the door, then rotate the top of the regulator through the opening while lowering the regulator to clear the top of the access opening. Align the holes in the regulator with holes in the door inner panel.
2. Install the door window regulator bolts and tighten to 89 inch lbs. (10 Nm).
3. Install new pull rivets. Install the upper left rivet first, followed by the lower right rivet.
4. Install the door window regulator cam bolt and cam nut and tighten both to 89 inch lbs. (10 Nm).
5. Attach the electrical connector, if equipped with power windows.
6. Install the door window. Please see Door Window Glass, Removal and Installation in this section.
7. Install the energy absorber (foam pad) and reposition the plastic sheet water deflector.
8. Install the door trim panel, as outlined in this section.

Hope helps (remember rated this).

Power Window Motor: Service and Repair
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
INSTALLATION
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

1. Raise and support the rear door window glass to the full up position.
2. Remove the interior door handle.
3. Remove the rear door speaker.
4. Remove the water shield.
5. Disconnect the rear door window regulator motor electrical connector.
6. Remove the rear door window regulator rivets.
7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
8. Installation is the reverse of the removal procedure, noting the following:
   • Cycle the door glass to make sure of engagement of the drive mechanism.
   • Remove the rear door window glass-to-regulator bolt or rivet.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
   • Secure the rear door window glass in the full UP position with tape.
   • Disconnect the window regulator motor electrical connector.
   • Remove the 2 window regulator nuts.
   • Remove the 3 window regulator motor bracket nuts.
   • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
   • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
   • Connect the window regulator motor electrical connector.
   • Remove the tape securing the rear door window glass in the full UP position.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
   • Install the window regulator motor
   • Remove the window regulator assembly.

Remove the window regulator motor