20 Most Recent 1992 Mitsubishi Pajero Questions & Answers


The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicle- cars, atv, trucks. forklifts, boats, excavators etc.

1992 Mitsubishi... | Answered on Jun 14, 2018


First check to see if coolant is flowing through radiator, check cooling fans to make sure they work when it reaches hot temperature. If it's not flowing, check thermostat to see if it's opening.

1992 Mitsubishi... | Answered on Mar 03, 2018


ECU has logged an error code. YOu need to read it out with a tester and then fix the reported problem or clear the error code.
ECU goes to safe mode with reduced power if certain errors are logged.
Regards Winfried

1992 Mitsubishi... | Answered on Nov 05, 2017


injector copper washer seal ,best ask a garage its not a easy job ,

1992 Mitsubishi... | Answered on Jun 27, 2017


check rear brake lines and rear slave cyl

1992 Mitsubishi... | Answered on Sep 19, 2016


take wheel off
undo few bolts and hammer it out and refit new one

1992 Mitsubishi... | Answered on Jul 17, 2016


fuel pump relay

1992 Mitsubishi... | Answered on Jul 17, 2016


According to the manual, it changes the engine operation from "Fuel Efficiency" to "Powerful" mode. I don't know exactly what the acronym stands for but when used it revs the engine to a much higher rpm before shifting. There is a button between the driver and passenger seat you can turn it on/off, it's not a 'warning' light

1992 Mitsubishi... | Answered on Jun 21, 2016


Are you a DIYer? I recommend a repair manual from auto parts store. It is easy to refer to, and you will want it next time anyway.

1992 Mitsubishi... | Answered on Jun 07, 2015


check the oil level of the gearbox, if level is low or oil is too thin will cause it to crunch. put an 80w90 gear oil into it if needs fill or change/ also check the clutch is fully disengaged. maybe clutch hydraulics have air in the system, this will reduce the travel of the clutch fork and not fully disengage the clutch. to see if its the clutch hydraulics select 1st gear push in the clutch and start the engine, if it starts to creep forward check out the hydraulics. if all this ok, prob be the synchro rings internal in the gearbox

1992 Mitsubishi... | Answered on Apr 01, 2015


NEVER use the pressure rating on the tire. That is only the recommended MAX pressure that tire can take. The only tire pressure you should follow is located on the placard either on the inside of the door under the latch, or on the door jam under the latch receiver. Using the tire pressure on the tire can result in poor performance, traction, tire blowouts, uneven tire wear, and poor gas mileage. The manufacturer factors in details the tire could never know, such as weight of the vehicle, alignment specifications, and performance of the vehicle.

1992 Mitsubishi... | Answered on Mar 11, 2015


I'm not sure I understand your question. When I first read it I thought you were saying you had an error code that the engine idle is low, but the error code you've given is for a MAP sensor problem which you mentioned in your post also. I'm going to guess that you've observed the low idle yourself, and when you ran the diagnostics the engine computer was complaining of a bad MAP sensor signal. This is triggered when the engine computer sees a change in another sensor that should correlate with a certain change in the MAP sensor, but the MAP sensor signal doesn't change as expected. Idle problems are a possible symptom of a bad MAP sensor, so this is not unreasonable. What your engine is telling you is that you should check the MAP sensor and its related wiring and hose connections to try to find your problem. If you fix the problem with the MAP sensor then your idle may start working properly again.

1992 Mitsubishi... | Answered on Feb 11, 2015


Replace it. if you look in the bottom of the door, you will probably find the parts that broke off or shavings of the plastic. I have never had any luck on fixing regulators. Some have worked for awhile, but still break again. I replace them all now. Not worth the time. The plastic is just to worn out.

1992 Mitsubishi... | Answered on Dec 06, 2014


The small wire to the starter is loose or failing to make a good connection it gets enough power ti click the solenoid but not engage the starter

1992 Mitsubishi... | Answered on Nov 28, 2014

Not finding what you are looking for?
1992 Mitsubishi Pajero Logo

191 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

84619 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Pajero Mitsubishi

  • Pajero Mitsubishi

Most Popular Question

pwr light came switch off

  • Cars & Trucks
Loading...