20 Most Recent 2011 Mazda CX-9 Questions & Answers

P1727 Auto Trouble Code - Auto Trouble Codes

https://p1727.autotroublecode.com P1727 Auto Trouble Code description with all kind of problem on car models. Find the repair process of P1727 OBD 2 engine fault code.

Common Trouble Codes ' DGTech

https://www.dgtech.com > common-trouble-codes P1727 Coast Clutch Solenoid Inductive Signature Malfunction; P1728 Transmission Slip Error; P1729 4×4 Low Switch Error; P1730 Gear Control Malfunction 2,3,5 ...

Do you have a check engine light on? Is the engine misfiring?

This is pretty much what the booster looks like. The brake master cylinder is connected to the two studs on the left. You only need to remove the studs and pull the master cylinder aside, being careful not to damage the brake lines. There will be a vacuum line attached to the engine compartment side of the booster as well. This must be disconnected. The rod extending from the bellows on the right is inside the vehicle and it connects to the brake pedal with a clip of sorts. Remove the clip and disengage the rod. Then, remove the two nuts holding the booster to the firewall (on the studs facing to the right, and pull the booster from the engine side. Installation is done by reversing the process.

You may need 2 keys to do this, possibly just one. My source does not specify if 1 key will work but here is the procedure i found With two programmed advanced keys

1. Bring the programmed advanced keys (2) and a unprogrammed advanced key into the vehicle.
2. Close all doors.
3. Insert the supplementary key into the ignition key cylinder. NOTE:

• Complete the procedures up to Step 7 within 30 s after the supplementary key is inserted.

1. Turn the ignition switch to the ON position.
2. Press the UNLOCK button on advanced key 1.
3. Press the UNLOCK button on advanced key 2.
4. From the ignition switch in the ON position, switch the ignition switch in the order indicated below.

• ACC->ON->ACC->ON->ACC->ON

1. Open the driver-side front door, press the door switch twice , and then close the door. NOTE:

• After Step 3 is completed and the advanced key programming mode is activated, the door lock actuator operates to lock, and then operates to unlock.
• If the door lock actuator does not operate, repeat the procedure from Step 2.

1. Press the UNLOCK button on the unprogrammed advanced key twice . NOTE:

• After Step 8 is completed and the advanced key is programmed, the door lock actuator operates to lock, and then operates to unlock.

1. If programming more advanced keys, remove the supplementary key once, and then repeat the procedure from Step 2.

low beam won't light Richard, faulty bulb socket module or wires, check and repair. Check the attached links,instruction and guides, Good luck "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." How to Fix Low Beam Headlight Low beam headlights out High beam working High beams ok but not low beam one side only TDIClub Forums

Immerse the car under water for 48 hours.

It is quite easily unblocked, there is a rubber tube extruding from the firewall, stick a long thin piece of something up it and clean it out, you shouldn't have any other problems, cheers hope this helps

Remote start is by bypassing the regular start system of car. The car is not reading the value for the transponder key and thinks the system has malfunctioned. (thus the red key light). He wired the remote start to by pass the cars theft system and start the car with the remotes brain and transponder value. At this point it get complicated as the cars computer was programed for a car without remote start when it was made. It won't hurt the car but some remote starts may need and additional module to trick the computer into thinking there is a key there when remote start is engaged so the red key light won't come on.

There is a problem with the antilock system, this system will effect TCS, brake and traction.

Flip open key. With small tweezers, file, or jewellers screwdriver, depress release button found in key-slot (near the end of the fob with the key on it. Pull two halves of fob apart. Separate the remaining fob in half again (the part without the key) by prying in the slot on the open end. Replace battery. Reassemble.

Forgot to use a memory saver,did ya? See an alarm specialist/car stereo shop . Re-connect cables and try again.Find car alarm wires and disconnect. Car alarm is designed to NOT let the car be started,if power is lost.

this is a long fastener with plastic both on the middle and near the fixture..look to see whats missing and replace it..there is an up and down..and a left right on both sides..