I have a crow-footed prybar that I can hook the master cylinder studs and leverage it to turn, but they do make a special tool that slides over the studs and has a 3/4" nut for a socket and break-over bar to accomplish the same thing.
Sadly we do not supply parts. All I can suggest is you visit a store that sells that tool or go the the manufacturer's website and contact them about replacement parts. You will probably need the serial and model number to make sure you get the correct parts.
Let's troubleshoot this problem step by step:
Linkage Adjustment:
The issue might be related to the linkage between the shift lever and the transmission. Sometimes, the linkage can become bent, broken, or jammed.
Inspect the linkage carefully. Look for any signs of damage or debris that might be obstructing its movement.
If you find any bent or broken parts, consider repairing or replacing them. Also, ensure that the linkage is properly lubricated according to the user manual.
Purging the Transaxle:
Try purging the transaxle to ensure smooth operation. Follow these steps:
Place the mower on a level surface away from any obstacles.
Turn off the engine and apply the parking brake.
Disengage the transaxle by moving the freewheel control to the disengaged position.
Check for Mechanical Obstructions:
Inspect the area around the gear shift lever and the transmission for any obstructions.
To reset your Innova 3100 OBD2 code reader, follow these steps:
Verify the Connection:
Ensure that the tool is connected to the vehicle's Data Link Connector (DLC).
Confirm that the ignition is ON.
Turn Ignition OFF and ON:
Turn the ignition OFF.
Wait for 5 seconds.
Turn the ignition ON again.
This process will reset the computer. If you encounter any issues, refer to your Innova 3100 Owner's Manual. INNOVA 3100 OWNER'S MANUAL Pdf Download ' ManualsLib
Your best option here is to visit a store that sells Bebe products or contact Bebe directly to find out if they supply repair parts or replacement hoods. We unfortunately don't supply parts, we simply provide advice for repairing things.
These pipes can be a pain in the tailbone to work with. Here's a trick to try. Do this when the engine is cold.
Get a cup sized container and half fill it with hot but NOT boiling water. Put about a finger's length of that end of the pipe into the water and let it heat up. This softens the pipe and can help it stretch to fit.
OK, more information please. What year is this Bakkie? What engine is in it?
What Exactly does it do when you try to start it?
Nothing at all at the key, just a 'Clunk' or a very lazy turn over suggests a flat or weak battery. Batteries do get old and weak especially if they're over 5 years old or on a bigger size engine. Try putting it on charge overnight and see if that helps.
Does it just spin and not try to start? This could be a 'No Spark' issue.
Does it turn over, try to start then immediately stall? This might be a fuel supply problem.
Dash lights only use a small amount of voltage so they are often the last thing to stop working.
Let's troubleshoot this issue:
Valet Mode:
First, check if the trunk is in valet mode. Some vehicles have a setting that prevents the trunk from opening using the key fob or the dash button when in valet mode.
Look under the trunk at the top of the license plate area. You'll find a key slot there. Use the physical key section of your key fob to open the trunk manually.
Child Locks:
Ensure that the child lock feature is not accidentally engaged. If it is, the trunk won't open from the outside handle switch.
Switch the child lock to the unlock position and try pulling the trunk handle again before closing the door.
Trunk Release Relay:
If the above steps don't resolve the issue, there might be an issue with the trunk release relay.
Check if there's ground at the switch in the glove compartment when you activate the release switch on the door, the trunk release on the key fob, or the rear handle.
Use a paperclip to jumper between the #30 and the #87 pin sockets of the relay. The pin numbers are usually labeled on the relay body.
Mechanical Issues:
Inspect the trunk latch mechanism for any signs of damage or obstruction.
Verify that the outside trunk handle is properly connected to the latch.
Hyundai azera trunk unlock Switch (youtube.com)
If necessary, consult a professional mechanic to diagnose and fix any mechanical issues.
Remember to follow safety precautions while troubleshooting, and if you're unsure, it's best to seek professional assistance.
The Jumper 850 uses an AC power module that outputs 12vdc @ 500 ma and has a cigar lighter plug on the end. The yellow light will light up when fully charged.
Check Battery Connections:
First, ensure that your battery connections are tight. Loose or corroded connections can prevent power from reaching the necessary components.
Try removing the battery cables and leaving them disconnected for about 15 minutes. Then, reconnect them to reset the system.
Steering Wheel Position:
Make sure the steering wheel is locked and that the transmission is completely in the park or neutral position. Sometimes, if the steering wheel isn't fully locked, it can interfere with starting the vehicle.
Ignition and Dash Lights:
If there are no ignition lights or dash lights when you turn the key, it could be due to several reasons:
Dead Battery: Most likely, a dead battery is the culprit. Even if the lights and accessories work, a weak battery may not provide enough power to start the engine.
Starter Relay or Solenoid: If there's no sound when you turn the key (not even a click), it might be an issue with the starter relay or starter solenoid.
Body Control Module, Instrument Cluster, or ECM: There could be a bad connection in the connectors to these modules. Try disconnecting the battery, then apply dielectric lube to the connectors before reconnecting it.
Fuse and Wiring Check:
Inspect the fuses related to the ignition system. A blown fuse could be causing the issue.
Also, check for any wiring issues that might disrupt the electrical flow.
Remember that diagnosing car problems can be complex, and it's often best to consult a professional mechanic or take your truck to a Ford dealer.
Check the Light Switch Position: Ensure that the light switch is indeed in the "off" position. Sometimes, it might appear to be off, but a slight misalignment can keep the lights on. Double-check by toggling the switch a few times.
Faulty Light Switch: Even if the switch seems fine, it could be faulty. Over time, switches can wear out or develop internal issues. Consider having a professional inspect and replace the switch if necessary.
Electrical Issues: There might be an electrical fault causing the lights to stay on. Inspect the wiring and connections related to the external lights. Look for any loose wires, damaged insulation, or corroded connectors.
Stuck Relay or Module: Modern cars use relays and control modules to manage various functions, including external lights. A malfunctioning relay or module could keep the lights on. A mechanic can diagnose and address this issue.
Faulty Light Sensors: Some vehicles have light sensors that automatically turn on the lights when it gets dark. If these sensors are malfunctioning, they might keep the lights on even during the day. Check if your car has such sensors and have them tested.
Battery Voltage Issues: Low battery voltage can cause electrical anomalies. Make sure your car battery is fully charged and in good condition. A weak battery might not provide enough power to fully turn off the lights.
Ignition Switch or Key Cylinder Issues: Faulty ignition switches or key cylinders can sometimes affect the electrical system. If the lights stay on even when the car is off, consider having these components inspected.
Remember that diagnosing electrical issues can be complex, especially without proper tools and expertise. It's advisable to consult a qualified mechanic or an auto electrician to pinpoint the exact cause and resolve the problem. They can perform diagnostic tests.
