20 Most Recent 2015 Hyundai Elantra - Page 2 Questions & Answers

If your saying when the problem is ongoing, the starter motor won't crank the engine, if you'll post model year, I'll try to post wiring diagram for starter motor, sometimes we can bypass everything just to see if starter motor will crank the engine? Any testing at starter motor make sure transmission is in park or neutral and parking brake is set. Vehicle can't move.

Hi is it that the safety belt it is surely the safety belt that has jammed in door if so get someone on outside to hold it in the open position and the other one inside to push hard with his feet,it some times take a kick to open from inside not saying you should but there you are some times it the only way. Take care all best to you. Clive

you pay to have it repaired

A screwdriver, but you need the target board that garages have. From a certain distance on flat ground, the beam has to hit the board in a certain way.

You need someone with a programming scan tool. https://www.programyourremote.com/classified/2017-hyundai-elantra-keyless-entry-remote-fob-smart-key-programming-instructions-listing-8720.aspx ..

https://www.fixya.com/cars/t29804314-adjustment_screws_2017_hyundai_elantra

Can anyone mark on this fuse box for FOG lights for Elantra 2015. There isnt too much about it on the internet.

https://www.cargurus.com/Cars/Discussion-t66940_ds1068808

120-130 ft lbs

I just got the same message today...and rarely use the cd player. Was wroking, went to change cd's, then it would not load and gave error 43...anyone?????

Im not sure if your fuse box looks like the screenshot however if it does I would at your own risk turn this switch off and back on as suggested in the other photo.
Again I am not a mechanic, I do however try to give the best advice I can.
Hope this helps.

Just for fun try unhooking your negative battery cable for a couple minutes to do a reset or reboot .

Check the fuse and relay related to the AC. Your fan should come on when the AC is turned on. Right now the fan is working only off the engine temp., not the AC.

Hose is held to suspension strut with c-clip, loosen and retighten union joint while still in clip for ease of undoing. then remove clip holding hose with pliers Top up reservoir and to avoid fluid loss, Clamp existing rubber hose off above Wheel cylinders callipers. Spread brake pads slightly to clear disc rotor edge then undo callipers from hub - suspend from strut with cord or wire and unscrew old pipe. Immediately replace existing with new hose to callipers. With master cylinder reservoir sealed airtight undo union nut at top of existing rubber hose where clipped to strut. Replace existing lower hose fitting with new hose.Tighten union. replace c clip and bleed brakes at nipple on callipers until all air out of lines. Job done road test for hard pedal repeat bleeding as necessary.

By pass clutch signal by appling +12vdc to A/C clutch directly - check for proper suction side pressure with A/C gauge connected to suction side of compressor - if pressure is low clutch will not be energized do to low pressure cutout switch. Add freon or 134A to bring up suction side pressure. https://www.6ya.com/callphilipforhelp

Sounds like the beginning of a bad 02 sensor. If your engine light is on that’s the issue. I could almost guarantee it. Any auto part store will read the ecu codes for free.

Under your dash there is a small lever with a handle and marking. pull this for ejecting the bonnet. use your palm to push off the safety lack that hold the bonnet- safety for holding on during high speed/ wind if the bonnet lack opens- to lift up your boonet. You can look through the gap of the bonnet to see this safety latch.
now on top of the engine you will see the cap for the oil inlet.
Now beffore you do that , use the dip stick to look for the oil level. wipe it and check again. Only if the oil is down you need to replace. Also topping is not required unless the engine is old/bad. otherwise it is important to change the oil filter and oil along with your service. So check this out. Good day

No compression may mean the timing belt has broken or slipped.

https://www.pistonheads.com/gassing/topic.asp?h=0&f=12&t=1150559