2009 BMW 3 Series - Answered Questions & Fixed issues
I have had intermittent hi pitch noise from the
possible belt noise. Does it happen with A/C on? Also have the bearings checked on the idlers and tensioner for the belt system. Ive had a 03 bmw 325i do something very similar. Let me know I am super curious if that is it
8/12/2013 3:12:15 AM •
2009 BMW 3...
•
Answered
on Aug 12, 2013
•
633 views
No power 2009 BMW 328I
Check the battery positive terminal it might be open. If the vehicle was in a accidents terminal might need to snap back into place or replace it if it's open
7/18/2012 9:36:37 PM •
2009 BMW 3...
•
Answered
on Jul 18, 2012
•
1,293 views
My 2007 BMW 525xi is
It sounds like a power steering pump problem. If you get low on power steering fluid the power steering pump will have a loud whining sound. The upper and lower control arm bushings will make a squeaking sound. And they would only make it when turning. I am sure that your power steering fluid is low.
10/5/2010 4:05:33 PM •
2009 BMW 3...
•
Answered
on Oct 05, 2010
•
195 views
1997 bmw 316i compact, thermostat??
it may be possible that your heater core was faulty and some has by passed it. open hood and check for incoming and outgoing heater hoses into firewall(dash of car). it is also possible that the heater core is plugged, try getting your cooling system flushed
5/14/2010 4:57:06 PM •
2009 BMW 3...
•
Answered
on May 14, 2010
•
961 views
Located fuse box in glove compartment, cannot find
The easiest way to do this would be just to check all the fuses. You can do this by pulling each one out and inspecting for burn marks and breaks on the inside. If you would, next time state the car model. Good luck.
5/3/2010 3:49:55 PM •
2009 BMW 3...
•
Answered
on May 03, 2010
•
85 views
How do you remove the front headrest for a 2009
You can't remove the front headrests from 2009 or later BMW's without first disconnecting internal wiring that runs inside 1 of the posts for each headrest to the inside the seat. This wiring is part of the Active Restraint Safety System that was new for 2009.
If you force it and break the wire you will at a minimum need to spend about $300 at the dealer to resplice the wire by taking the back off the seat.
3/12/2010 8:05:16 PM •
2009 BMW 3...
•
Answered
on Mar 12, 2010
•
925 views
Bmw misfiring
I would check your tps(Throttle positioning sensor) to see if its bad. That's what it sounds like.
9/22/2009 2:59:50 PM •
2009 BMW 3...
•
Answered
on Sep 22, 2009
•
835 views
Can you tell me whee to find the thermostat on a
Hi,
If you are referring to the coolant thermostat, though I'm not familiar with your model, basically thermostats are located in a housing on the engine where the top radiator hose connects to that housing. For the most part, they are pretty easy to replace. If you have an overheating problem with your car, I hope this fixes it.
8/27/2009 1:47:46 PM •
2009 BMW 3...
•
Answered
on Aug 27, 2009
•
139 views
My bmw 320d remote wont
1
Programming
When
Key batteries completely discharged. Key batteries not replaced within 60 seconds. Key added or replaced. DO NOT press remote control buttons during battery replacement.
How
Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button Fig. 1 [1]. Press lock button Fig. 1 [2] briefly 3 times within 10 seconds keeping unlock button [1] depressed. Release unlock button Fig. 1 [1]. Some models: LED Fig. 1 [3] flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Some models: Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously
Later keys with bmw badge on key. Battery can not be replaced
Battery in key charges while driving
3/15/2018 11:14:51 AM •
BMW 3 Series...
•
Answered
on Mar 15, 2018
•
1,368 views
Eml light.. loss of power
Hi
Air flow sensor could be a problem.
Every time EML comes on the car computer will put the system into limp mode. To avoid any further damage to the engine.
once switch off, isolated and re-start will re-run the program and clear it temporary.
Ideally you need to get the car plugged in to a Diagnostic computer and see what fault code are stored.
Thanks
2/6/2018 10:09:06 AM •
BMW 3 Series...
•
Answered
on Feb 06, 2018
•
2,431 views
My new BMW 3.16 (20100
no , neither am I
no manufacturer will release a substandard vehicle
check for broken exhaust pipe flex section near the manifold and a failing cat converter blocking the exhaust system
12/20/2017 4:48:56 AM •
BMW 3 Series...
•
Answered
on Dec 20, 2017
•
62 views
Not finding what you are looking for?