nail gun fixer
yoopertech posted an answer for this Duo Fast DuoFast DF350S 20? Round Head Framing Nailer:
"Must remove magazine and there will be a c-clip. Take off feeder pawl and spring and it..."
yoopertech posted an answer for this Air Tools & Compressors:
"No parts available for Central. Throw away tool."
yoopertech posted an answer for this Air Tools & Compressors:
"The nails load thru the top of the magazine."
yoopertech posted an answer for this Stanley Bostitch Sb 2IN1 2 In 1 Narrow Crown Stapler/18 Gauge Brad Nailer:
"If it's a gas unit, clean and lube. If an air unit, take of the cap and dump some air..."
yoopertech posted an answer for this Air Tools & Compressors:
"Buy new pressure relief valve, I have in stock."
yoopertech posted an answer for this Air Tools & Compressors:
"Look at the lower bumper and cylinder sleeve check seal."
yoopertech posted an answer for this Air Tools & Compressors:
"U have to take the magazine bolts off the nose. Sometimes you can pond driver blade back..."
yoopertech posted an answer for this Craftsman Nailer Kit, Palm Air Driver:
"Must need a cleaning and lube. Or you need a magazine spring."
yoopertech posted an answer for this Duo Fast Air Tools & Compressors:
"Sounds like the lower bumper is shot."
yoopertech posted an answer for this Air Tools & Compressors:
"Sounds like the Capacitor is shot. I have in stock."
yoopertech posted an answer for this Tools & Hardware - Others:
"You have to take the top cap off and the bottom nose off to remove Driver Poppet assembly."
yoopertech posted an answer for this Hitachi Tools & Hardware - Others:
"Bad trigger switch(circuit board)"
yoopertech posted an answer for this Hitachi Tools & Hardware - Others:
"Sounds like a bent nose. It's been dropped"
yoopertech posted an answer for this Tools & Hardware - Others:
"Bad Bumper inside or broken driver blade."
yoopertech posted an answer for this Tools & Hardware - Others:
"Bad bumper inside."
yoopertech posted an answer for this Hitachi NV45AB2 Roofing Coil Nailer :
"Safety might be bent. You drop it?"
yoopertech posted an answer for this Tools & Hardware - Others:
"airnailerparts.com"
yoopertech posted an answer for this Senco Air Tools & Compressors:
"2" to 3 1/2" 2" for sheathing and 3 1/2" for stud framing."
yoopertech posted an answer for this Air Tools & Compressors:
"17 degrees I have some left. Nobody carries them anymore!"
yoopertech posted an answer for this Air Tools & Compressors:
"no parts for Harbor Freight nailers. Throw away tools."
yoopertech posted an answer for this Stanley Air Tools & Compressors:
"http://servicenet.bostitch.com/ Bostitch ServiceNet"
yoopertech posted an answer for this Air Tools & Compressors:
"type in your model# and Bam! There it is! http://servicenet.bostitch.com/ Bostitch..."
yoopertech posted an answer for this Stanley Bostitch MIIIFN Flooring Nailers:
"Is the bottom of the shoe on the sub floor?"
yoopertech posted an answer for this Hitachi NR90GC 3 1/2" Gas Powered Clipped Head Framing Nailer:
"Could be bad gas canister or needs cleaning. How many boxes of nails You shot thru that..."
yoopertech posted an answer for this Hitachi NR90GC 3 1/2" Gas Powered Clipped Head Framing Nailer:
"Did You drop it? AirNailerParts Nailer Parts"
yoopertech posted an answer for this Stanley Bostitch STB-MIIIFS Flooring Stapler:
"Must take top and bottom off tool for the driver assembly to be removed."
yoopertech posted an answer for this Tools & Hardware - Others:
"I have o'rings , but no hard parts."
yoopertech posted an answer for this Tools & Hardware - Others:
"They are a finish T-Nail."
yoopertech posted an answer for this Tools & Hardware - Others:
"You might want to check. I think that was recalled."
yoopertech posted an answer for this Tools & Hardware - Others:
"Did You remove the exhaust seal. That could have got pinched. I have in repair kit. ..."
yoopertech posted an answer for this Hitachi NR90AD 3 - 1/2'' Clipped Head Strip Nailer:
"O'ring kit will fix it. AirNailerParts Nailer Parts"