Vincente
vinhson65 posted an answer for this Whirlpool Cabrio WTW6600SBT Top Load Washer:
"UL means unbalanced load was detected in your washer. Try to stop the washer and..."
vinhson65 posted an answer for this Kenmore Elite HE5t Washer:
"F21 means long drain. Yes, there is something be in the hose. You need to open the filter..."
vinhson65 posted an answer for this Maytag Centennial MTW5800TW Top Load Washer:
"This unit does not handle a super large load as it advertised. When you put a super large..."
vinhson65 posted an answer for this Maytag Centennial MTW5800TW Top Load Washer:
"Remove the top so you gain access to manual unlock the lid. Remove two screw on top of the..."
vinhson65 posted an answer for this Maytag Centennial MTW5800TW Top Load Washer:
"There are two hinges at the back, just remove two screws on top then push the top toward..."
vinhson65 posted an answer for this EuroTech Washing Machines:
"It seems no bearing kit for this model. The drum bearing is hard to replace and seal it..."
vinhson65 posted an answer for this Maytag Washing Machines:
"LF means long fill. Firstly, check the screen on the water inlet if there is any debris,..."
vinhson65 posted an answer for this Maytag Centennial MTW5800TW Top Load Washer:
"The second switch from the left to right was bad. It needs replacing with a new one."
vinhson65 posted an answer for this Maytag Washing Machines:
"Grinding sound is obviously the symptom of bad bearing. You need to replace the bearing."
vinhson65 posted an answer for this Kenmore Washing Machines:
"Your model does not right so it is hard to find the main root cause. It may have the issue..."
vinhson65 posted an answer for this Washing Machines:
"What kind the washer is? If the front load, there are 4 shipping bolt at the back to keep..."
vinhson65 posted an answer for this Washing Machines:
"It could be the pump is restricted and would not pump all the water out. The pump should..."
vinhson65 posted an answer for this Bosch Washing Machines:
"E3 means the door lock somehow does not work properly. The door lock may need replaced...."
vinhson65 posted an answer for this Washing Machines:
"You may have the main control board goes bad."
vinhson65 posted an answer for this Kenmore 15864/15862 Top Load Washer:
"This is Sears product, call the Sear part center and tell them your model, they will find..."
vinhson65 posted an answer for this Maytag Ensignia 3.3 cu. ft. Top Load Washer:
"If it comes from the bottom, motor and belt need to be checked. If it comes from the top,..."
vinhson65 posted an answer for this Washing Machines:
"If the drum is freely turn then there is no issue with drum blockage. Tighten the nut that..."
vinhson65 posted an answer for this Washing Machines:
"Those parts you can check 1/ strings holding the drum were broken causing drum unbalancing..."
vinhson65 posted an answer for this Washing Machines:
"This is not a easy job, you may need service man to do it. Anyway, use putty knife to find..."
vinhson65 posted an answer for this Washing Machines:
"Please provide model to figure out the issue."
vinhson65 posted an answer for this Whirlpool WFW94HEX Washer:
"Great! you have the MCU (motor control unit) need to replace. Removing the rear panel so..."
vinhson65 posted an answer for this General Electric WH12X10138 Control Assembly:
"Go this link if it would help...."
vinhson65 posted an answer for this Kenmore 44102 Front Load Washer:
"It seems the tub bearing went to it end cycle. The cost of repair is as high as buying the..."
vinhson65 posted an answer for this Whirlpool Washing Machines:
"Need to know what unit is (top/front load) If top load, the timer may bad. If front load,..."
vinhson65 posted an answer for this Washing Machines:
"Hard to tell, need model to figure out (top/front load)"
vinhson65 posted an answer for this Washing Machines:
"The service manual is hidden inside the unit or inside the console."
vinhson65 posted an answer for this Whirlpool Ultimate Care II LSQ9564J Top Load Washer:
"You can find it somewhere inside the console on the top."
vinhson65 posted an answer for this Whirlpool Ultimate Care II LSQ9564J Top Load Washer:
"This issue calls siphoning effect. It happens when the drain hose was somehow lower or not..."
vinhson65 posted an answer for this Whirlpool WFW9050X Washer:
"You should check the hot/cold water from wall to the inlet of washing machine, make sure..."
vinhson65 posted an answer for this Whirlpool Duet GHW9150P Front Load Washer:
"It may have F21 code together meaning long drain in the system. Open the small top toe..."
vinhson65 posted an answer for this Whirlpool Duet GHW9150P Front Load Washer:
"Can search on Google to buy a new baffles then just slide in the new one to replace the..."