Do it right (what are the options again?).
Anonymous posted a question about Cell Phones:
"My wife washed her LG rumor. Everything works but the microphone. I have figured out how..."
Anonymous posted an answer for this Bernina 1008:
"that is your problem, your needle bar is centered too far to the back. There are 2 little..."
Anonymous posted an answer for this Sewing Machines:
"if you adjust that setting, check that the needle goes into the needle plate the exact..."
Anonymous posted an answer for this PfaFF Sewing Machines:
"Is the machine older? If it is, it could be sticking. Try using sewing machine oil on it...."
Anonymous posted an answer for this Sewing Machines:
"oil the shaft for the presser bar and keep moving it up and down(it may take a while)..."
Anonymous posted an answer for this Husqvarna Viking 1:
"Hi, On that machine, the cassettes aren't actually computer chips. Each cassette has a..."
Anonymous posted an answer for this Sewing Machines:
"Hi, This may sound crude, but you can tape a piece of thin cardboard over the teeth. Be..."
Anonymous posted an answer for this Brother LS-2125 Mechanical Sewing Machine:
"Here are some things to try: Big loops are actually easier to solve usually. 1st know..."
Anonymous posted an answer for this White Sewing Superlock 2000 ATS Mechanical Sewing Machine:
"alI it takes the exact same needle as a home sewing machine (130/705H or HAx1 or HAX1SP)..."
Anonymous posted an answer for this Sewing Machines:
"On most models you can use a dremel or a file to help "flatten" the spot that the presser..."
Anonymous posted an answer for this Sewing Machines:
"adjust the stitch width to "0". If it still needs adjusting, somehting is sticking in the..."
Anonymous posted an answer for this Sewing Machines:
"Hi, The Kenmore is made by Janome. The Janome has a little cam (lever) that when flipped,..."
Anonymous posted an answer for this Bernina 1008:
"Hi, There is a spring loaded catch on the needle bar assembly. It is designed to keep the..."
Anonymous posted an answer for this Sewing Machines:
"Hook Timing: To time the machine, you want the tip of the hook to pass just over the top..."
Anonymous posted an answer for this Brother LS-1217 Mechanical Sewing Machine:
"Hi, Open the end where the light is, look for a set screw at the point where the tension..."
Anonymous posted an answer for this Sewing Machines:
"Dropped stitches troubleshooting: 1>change to a new proper needle (proper needle means..."
Anonymous posted an answer for this Husqvarna Viking 1:
"Hi, It sounds like the screen has lost calibration. If you can get into "set" touch more..."
Anonymous posted an answer for this Simplicity Denim Star SW210:
"Hi, Usually this problem occurs on machines with a front load bobbin case. If so, remove..."
Anonymous posted an answer for this Husqvarna Viking 1:
"sounds like the motor belt came off the machine, your description makes that sound exactly..."
Anonymous posted an answer for this Husqvarna Viking 1:
"The designer 1 has a weakness of the reverse pad (rubber button set) on left side of the..."
Anonymous posted an answer for this Husqvarna Designer I:
"1>Turn on machine 2>touch PROG (menu on top) 3>insert desired font disk 4>touch floppy..."
Anonymous posted a question about Air Tools & Compressors:
"What nail gun I can use to roof my home & also using it for framing. I just don't want to..."
Anonymous posted an answer for this Brother LS-2125 Mechanical Sewing Machine:
"try this: Tension: If the thread is loose on the bottom of the fabric, it's actually the..."
Anonymous posted an answer for this Sewing Machines:
"Sounds like it could be thread, try this: Thread test Test your thread quality to start,..."
Anonymous posted an answer for this Husqvarna Husky 165:
"the eyes of the needles must line up with lower looper as they pass (timing) the distance..."
Anonymous posted an answer for this Husqvarna Viking 1:
"the transformer has broken solder connections between the pins for the plug and the..."
Anonymous posted an answer for this Husqvarna Viking 1:
"try threading the bobbin by lifting the presser foot, and pulling the thread under the..."
Anonymous posted an answer for this Husqvarna Viking 1:
"drop in bobbin, only goes in one way (you can't do it wrong. follow white on white arrows..."
Anonymous posted an answer for this Husqvarna Viking 1:
"Looping on bottom: Great description, that helps a lot. Big loops are actually easier to..."
Anonymous posted an answer for this Husqvarna Huskylock Computerized 910:
"the ribbon cable may have wiggled loose. It plugs in right behind the tension assemblies..."
Anonymous posted an answer for this Husqvarna Viking 1:
"you cannot convert a #'d embrodiery card collection to areadable/writeable card. If it has..."