1
Anonymous posted an answer for this Sewing Machines:
"Contact Steve at www.stevessewandvac.com they have alot of parts machines they can help."
AnonymousAnonymous posted an answer for this Baby Lock Ellure:
"You probably are in need of a new bobbin case they are plastic and oif you have broken a..."
AnonymousAnonymous posted an answer for this Baby Lock Ellure:
"You probably are in need of a new bobbin case they are plastic and oif you have broken a..."
AnonymousAnonymous posted an answer for this Baby Lock Ellure:
"You need to make sure that the embroidery arm is able to move freely be sure that it has..."
AnonymousAnonymous posted an answer for this Baby Lock Ellure:
"The pins in the embroidery card slot may have gotten bent causing the main board to short..."
Anonymous
Anonymous posted an answer for this Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum:
"These are two different problems the first could be a clogged heater soap coagulates in..."
AnonymousAnonymous posted an answer for this Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum:
"These are two different problems the first could be a clogged heater soap coagulates in..."
Anonymous
Anonymous posted an answer for this Hoover Floormate H3000 Upright Wet/Dry Vacuum:
"Not sure if this will help but these machines are ment to be used in one direction not..."
AnonymousAnonymous posted an answer for this Hoover Floormate H3000 Upright Wet/Dry Vacuum:
"It is unlikely that you have worn the brushes to the point that they no longer contact the..."
Anonymous
Anonymous posted an answer for this Hoover Vacuums:
"Flip the vacuum over push the pedal so the vacuum lays flat on the floor or table. Remove..."
AnonymousAnonymous posted an answer for this Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum:
"The mixer valve is most likely gummed up with old soap and stuck you will need to take the..."
AnonymousAnonymous posted an answer for this Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum:
"If the unit is spraying ok but your just not getting hot water you could have a defective..."
AnonymousAnonymous posted an answer for this Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum:
"Check to see if you get water from the hand held nozzle if so you have a clogged heater.If..."
Anonymous
Anonymous posted an answer for this Bissell 9200 Upright Vacuum:
"These are two different problems the first could be a clogged heater soap coagulates in..."
AnonymousAnonymous posted an answer for this Bissell Vacuums:
"Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber..."
AnonymousAnonymous posted an answer for this Black & Decker Vacuums:
"Unfortunately those units are prone to breakage they are also usually a sealed unit (not..."
AnonymousAnonymous posted an answer for this Hoover Vacuums:
"Needs a belt visit www.stevessewandvac.com they have on for your unit."
AnonymousAnonymous posted an answer for this Miele Vacuums:
"First remove the lid by opening it and pulling straight up while using a screw driver to..."
AnonymousAnonymous posted an answer for this Bissell Vacuums:
"There is a black rectangular seal under the front of the tank that seals to the top of the..."
AnonymousAnonymous posted an answer for this Vacuums:
"All of the hoover cleaners use air to spin the brushes the air intake is probably clogged...."
AnonymousAnonymous posted an answer for this Vacuums:
"If this unit has an onboard heater ( a little red lite in the center of the handle) then..."
Anonymous
Anonymous posted an answer for this Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum:
"Visit www.stevessewandvac.com you may not see it on the web but call or contact by email..."
AnonymousAnonymous posted an answer for this Hoover Vacuums:
"The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum..."
AnonymousAnonymous posted an answer for this Vacuums:
"The best way to check to see if you need a belt on your vacuum cleaner of any brand is to..."
Anonymous
Vacuums 19 answers
Sewing Machines 5 answers
