Looking to Retire
Chuck Nelson posted an answer for this Air Tools & Compressors:
"At 50 degree temperature outside use antifreeze in place of oil"
Chuck Nelson posted an answer for this Hitachi NV45AB2 Roofing Coil Nailer :
"Needs a trigger kit with the ball"
Chuck Nelson posted an answer for this Makita Roofing Coil Nailer AN451:
"Replace the piston stop in the head valve"
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"DO NOT USE WD40 . Is The Nailer fireing? If Not check the micro switch by the fan . Make..."
Chuck Nelson posted an answer for this Grip Rite Grip - Rite 21 Round Head Framing Nailer - GRTRH350:
"Nelsons Airtool Service 2006 Calico Rd Marion Il 62959 618-997-2101"
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Check the micro switch by the fan. It has a small roller on it. Lightly bend it to give..."
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Check the small switch at the top by the fan . It has a small roller on it.This trips the..."
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Check Bumper and Check valve in lower assy. If part of the check valve is craked it will..."
Chuck Nelson posted an answer for this Campbell Hausfeld 3 1/2" Rh Fram Nailer:
"The tool is being run with restricted air. Change fittings to industrial free fkow and..."
Chuck Nelson posted an answer for this Impact Ingersoll-Rand 1 Inch Heavy Duty Air Wrench 295A:
"Dave The rotor is too tight on the plate. Tap shaft with fiber mallet to open the..."
Chuck Nelson posted an answer for this Hitachi NR83A2S Framing Nailer, Full Head, Plastic Strip Collation :
"Check and make sure your using the right nails. Are they held together with plastic? This..."
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Check the oring and also the reeds on the lower end of the cylinder"
Chuck Nelson posted an answer for this Air Tools & Compressors:
"It is an import stapler similar to a Bostitch. The oring inside the poppet valve is worn...."
Chuck Nelson posted an answer for this Air Tools & Compressors:
"If you are using the nailer rapidly and the outside air temp is 50 degrees or less use..."
Chuck Nelson posted an answer for this Air Tools & Compressors:
"The oring on the cylinder is leaking past the bulkhead and out the nose . Does the driver..."
Chuck Nelson posted an answer for this Air Tools & Compressors:
"There is a cracked seal on the firing valve. It looks like it cant be replaced but it can...."
Chuck Nelson posted an answer for this Makita AN451 Coil Nailers:
"You are using a small automotive fitting and have the air pressure too high. Go to bigger..."
Chuck Nelson posted an answer for this Senco SNS41 16Ga Stapler 1" 2":
"No the short staples will not have enough holding power. The staples need to allow the..."
Chuck Nelson posted an answer for this Makita AF503 2'' 18 - Gauge Brad Nailer:
"Take head off of tool. Clean and lube orings on the head valve . Do not use wd40 use air..."
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Check the reed plate in the lower housing"
Chuck Nelson posted an answer for this NRS Paslode 501000 Powermaster Plus Clipped Head Nailer:
"Take 4 bolts off of head . Clean and lube head valve with air nailer oil. Not wd40"
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Check plug in on the fan . Have you taken the two halves apart? Check all connections . If..."
Chuck Nelson posted an answer for this Stanley Factory Reconditioned Bostitch U/RN46 1 1 3/4" Coil Roofing Nailer:
"The spring is located under the head valve.Turn the head upside down put in the spring and..."
Chuck Nelson posted an answer for this RTO PasLode 900420 Impulse Framing Nailer :
"Make sure the spark plug ignites. Take tool apart as in cleaning. Hold micr switch near..."
Chuck Nelson posted a question about Air Tools & Compressors:
"Parts manual for Nesco 3/4 '' Impact wrench all metal"