i'm a big deal
Kenneth posted an answer for this Electrical Supplies:
"The button, hose or switch has gotten a hole in it. They have a complete replacement kit..."
Kenneth posted an answer for this Curtis DVD8017 Portable DVD Player:
"you can click on this link to order the adaptor this will work, make sure your model..."
Kenneth posted an answer for this Dometic Rooftop RV Air Conditioner:
"before you figure it's out of freon- there are coil cleaners you can get at a air..."
Kenneth posted an answer for this Whirlpool LGB6300 Gas Dryer:
"there is a flame sensor/ thermocouple where the flame is, it's not picking up the heat off..."
Kenneth posted an answer for this Welding Tools:
"you are going to need to remove the wires going to the wire feed motor, then take a volt..."
Kenneth posted an answer for this Microwave Ovens:
"you can take the bottom panel off from underneath. the motor is there. you can take a..."
Kenneth posted an answer for this Kenmore Elite Oasis 27052 Top Load Washer:
"somewhere on the new motor you installed there is a amp/volt sticker. you should find it..."
Kenneth posted an answer for this Whirlpool LER5636P Electric Dryer:
"the flame sensor is giving a no flame reading. sometimes i take a small piece of sand..."
Kenneth posted an answer for this Intermatic & Indoor/Outdoor Rain Tight Timer :
"john, i'm assuming the water heater is 240 volts and the timer is 240 volts, if ok follow..."
Kenneth posted an answer for this Carlon Home Products Ballast Light Control, 1800 Watts:
"yes the other wires where probably for switching half of the bulbs in the fixture"
Kenneth posted an answer for this Hardware & Accessories:
"after you program the door, you have to push "sel" and override the load until the next..."
Kenneth posted an answer for this Lincoln Electric Ranger Gxt 250 Amp Generator/Welder 125 Volt, 250 Amp, Model# K2382 2:
"there are oil pressure and sometime temperature sensors on the motor. you can find these..."
Kenneth posted an answer for this Hardware & Accessories:
"you should be about to find it here--- ..."
Kenneth posted an answer for this TORK Digital Interval Timer Ssa100r-24:
"The timer should have came with a dark and light colored tabs. they must be put exactly..."
Kenneth posted an answer for this Parmak Solar Fence Charger :
"did you make sure the fence isn't grounded or an insulator hasn't melted"
Kenneth posted an answer for this Leviton 8599 GFCI Receptacle:
"if it is a gas bulb (mercury vapor, metal halide, or high pressure sodium) the bulb needs..."
Kenneth posted an answer for this Generac 5622 GP Series GP5000 6,250 Watt 389cc OHV Portable Gas Powered Gen:
"fuel problem, the float in the carborator is stuck, if you tap on the carborator bowl it..."
Kenneth posted an answer for this Flotec Simer//Omni 2957 Submersible Sump Pump with Piggyback Tethered Vertic:
"it sounds like it could be a bad float switch but most of the time the water isn't high..."
Kenneth posted an answer for this Little Giant Rs-5 Remote Switch:
"there is a breather tube that has to be above the water level, you can check the diaphragm..."
Kenneth posted an answer for this Guardian Electrical Supplies:
"the instructions says the voltage regulator is automatic/digital. when you check the..."
Kenneth posted an answer for this Leviton 8299 Combination Switch / Smart lock GFCI Outlet:
"power coming in from the breaker box: black wire will go to line-hot screw, and the white..."
Kenneth posted an answer for this Leviton R01-7299-0NI Switch And GFCI Outlet:
"power coming in from the breaker box: black wire will go to line-hot screw, and the white..."
Kenneth posted an answer for this Clarke Power Products Clarke 130EN Mig 110 Volt:
"ive got a crapsman mig welder that does the same thing, i took it apart and the..."
Kenneth posted an answer for this NRS Paslode 501000 Powermaster Plus Clipped Head Nailer:
"it's usually one of the "O" rings not sealing the air completely. it will probably get..."
Kenneth posted an answer for this Orbit Hardware & Accessories:
"the should be a pump or master solenoid connection inside the controller"
Kenneth posted an answer for this Hitachi EC12 Portable Electric 2hp Air Compressor, Oil Lubricated:
"you should take the cover off where the pressure switch is (the on off switch) and see if..."
Kenneth posted an answer for this Air Tools & Compressors:
"there are "0" rings in the compressor, if the compressor is less than $200 it's a "throw..."
Kenneth posted an answer for this Clarke Air Tools & Compressors:
"which parts do you need, usually compressor oil can be found at any hardware store, less..."
Kenneth posted an answer for this Measuring Tools & Sensors:
"i think you should be able to click on the link: ..."